Effects can often be rebuilt with the other DAW's devices. Instruments are harder: every synth has its own engine, and a different synth set to "similar" values can sound nothing like the original. This guide explains which instruments DAWPORT converts between FL Studio and Ableton Live, why it leaves the others alone, and what happens to your notes in each case.
2 free conversions every month. No card required.
The short version
| In your project | FL Studio → Ableton Live | Ableton Live → FL Studio |
|---|---|---|
| Third-party VST2/VST3 instrument | Same plug-in, with its state where supported | Same plug-in in FL's wrapper, with its state where supported |
| FL Sampler channel / Live Simpler | Simpler | Sampler channel |
| FL 3x Osc (basic shapes) | Operator (approximation) | — |
| Live Drum Rack or Instrument Rack | — | One channel per pad or chain, when every chain qualifies |
| Other DAW-own synths | Not converted; notes kept on a MIDI track | Not converted; notes kept on an empty channel |
| Complex samplers (DirectWave, FPC, Slicex; Live Sampler, Impulse, Drum Sampler) | Not converted; notes kept | Not converted; notes kept on an empty channel |
Why most stock synths are not swapped
FL Studio's own instruments only run inside FL Studio, and Live's only run inside Live. DAWPORT does not translate one synth engine into another. Sytrus is not rebuilt as Wavetable, and Operator is not rebuilt as an FL synth. A substitute patch would be a guess, and a confident-looking wrong sound is worse than a clear note telling you what to replace.
The one exception is FL Studio's 3x Osc, because its basic shapes can be played by Live's Operator (more below). Sample players are also converted, because the sample is the sound: FL's Sampler channel and Live's Simpler share the basics.
What happens to the notes of an unconverted instrument
This depends on the direction, so check it before you convert.
FL Studio to Ableton Live: the notes stay. The channel becomes a Live MIDI track with all its clips and notes, but no instrument. The conversion notes say, for example, "Sytrus could not be reproduced and was not inserted. Other project content was converted." Load any instrument on the track and keep working. Keep your original FL Studio project: it still holds the synth's settings. More in FL Studio synths in Ableton.
Ableton Live to FL Studio: the notes stay too. The track becomes an empty FL Studio channel holding the notes of its Arrangement clips, with no instrument loaded. The conversion notes say, for example, "Operator could not be reproduced and was not inserted." Load an FL Studio synth or a plug-in on that channel. More in Ableton synths in FL Studio.
To keep the exact sound instead, render the part to audio before converting: in Live 12 with Bounce Track in Place or Bounce to New Track (Ableton manual), in FL Studio with Consolidate (Image-Line manual). The audio travels as a normal sample. See stems vs project conversion.
FL Studio 3x Osc to Ableton Operator
3x Osc is a three-oscillator synth with sine, triangle, square, saw, rounded saw, noise and custom shapes (Image-Line manual). Since DAWPORT 1.0.70, a 3x Osc using the basic shapes becomes an Operator in Live, labelled as an approximation:
- Carried: the shapes (sine, triangle, square, saw, rounded saw and noise), each oscillator's level, coarse and fine tuning, and the channel's volume envelope (its hold stage folded in, curve shapes not carried). Channel volume and pan go on a Utility after it.
- Approximated: saw, square, triangle and rounded saw use Operator's own shapes, which are close rather than identical. Noise becomes an Instrument Rack with two Operators panned left and right, for a stereo noise sound.
- Left out, and noted: stereo phase offset and stereo detune.
- Not read: the channel filter, pitch envelope, LFOs, arpeggiator and mono/portamento settings.
The whole 3x Osc is not converted, and its notes stay on a MIDI track as above, when:
- Osc 3 is used as an amplitude modulator
- phase randomness is on
- an audible oscillator is phase-inverted or panned off centre
- an audible oscillator uses the custom (sample) shape
- any 3x Osc control is automated
The note reads: "3x Osc was converted to Operator in Ableton Live as a close approximation; it may sound slightly different. Some of its settings were not carried over." There is no reverse mapping: Operator does not become 3x Osc.
Sampler channel and Simpler
FL's Sampler channel and Live's Simpler convert in both directions. The sample, tuning, start and end points, reverse, volume and pan carry over, and the volume envelope does too (from FL Studio since 1.0.70; from Live in simple cases). Filters, LFOs and Simpler's warp, loop and slice modes are not rebuilt. The control-by-control table is on Simpler and Drum Rack in FL Studio.
When several FL channels play through one Mixer insert, each gets its own track in Live inside a Group track that holds the insert's effects. See mixer routing.
Drum Racks and Instrument Racks to FL Studio
A Drum Rack holds one chain per pad, and an Instrument Rack holds chains with key and velocity zones (Ableton manual). FL Studio has no direct equivalent, so DAWPORT splits the rack:
- The rule: every chain must hold exactly one Simpler or one third-party instrument plug-in. A chain may hold one nested rack instead, following the same rule.
- Result: one FL Studio channel per chain, all routed to the track's Mixer track. Each channel gets only the notes its pad, key zone or velocity zone played, and chain volume and pan are applied.
- All or nothing: if any chain holds something else, such as Operator, Sampler or Drum Sampler, or a sample is missing, the whole rack is not converted, and its notes do not reach FL Studio.
- Not carried: choke groups, pad sends to the rack's return chains, effects inside a chain, instrument rack macros and chain selector automation. Choke groups and pad sends are listed in the notes.
Rebuild choke groups with FL Studio's cut groups in the channel settings. DAWPORT does not build an FPC.
Pitch slides and pitch bend
- FL Studio to Live: slide notes become per-note pitch movement only on Sampler channels and 3x Osc channels. On other instruments, slides stay at their base pitch.
- Live to FL Studio: per-note pitch bend becomes FL slide notes on Sampler channels converted from Simpler and on channels built from racks. On a plug-in instrument track, the bend is dropped and the note says its base note remains playable.
Checklist
- Before converting from Live, render or swap tracks that use Live synths, Sampler, Impulse or Drum Sampler.
- Make sure every pad of a Drum Rack holds one Simpler or one plug-in.
- Install your third-party instruments in the destination DAW, in the same format.
- After converting from FL Studio, load new sounds on the MIDI tracks left without an instrument.
- Read the conversion notes for every instrument listed as not converted.
Ready to try it? Convert FL Studio to Ableton Live or Ableton Live to FL Studio.

