It is the first question most producers ask before switching DAWs: will my plug-ins still work? The answer depends on what kind of plug-in it is. This guide splits them into three groups and explains what DAWPORT does with each.
2 free conversions every month. No card required.
| Plug-in type | Examples | What happens when you convert |
|---|---|---|
| Third-party VST2/VST3 | Synths and effects from other developers | Kept, with their saved settings, where supported. You install them in the other DAW. |
| Stock effects | Fruity Limiter, Fruity Parametric EQ 2, EQ Eight, Glue Compressor | Replaced with the other DAW's own device where DAWPORT has a mapping, labelled as an approximation. |
| DAW-only instruments and effects | Sytrus, Harmor, Gross Beat, Operator, Wavetable | Not converted. Listed in the conversion notes. What happens to the notes depends on the direction (see below). |
Third-party VST2 and VST3 plug-ins
Both DAWs load the common plug-in formats. FL Studio supports VST2, VST3 and CLAP, plus Audio Units on Mac (Image-Line manual). Ableton Live supports VST2 and VST3, plus Audio Units on Mac (Ableton manual). So a plug-in you bought from another developer can usually run in both, if your licence lets you install it.
When you convert, DAWPORT writes each supported VST2 or VST3 plug-in into the new project together with its saved state, so the preset and knob settings you dialled in come along.
- FL Studio to Ableton Live: the plug-in becomes a normal plug-in device in Live with its state.
- Ableton Live to FL Studio: the plug-in goes into FL Studio's plug-in wrapper with its state.
Three things matter on your side:
- Install the plug-in in the destination DAW. DAWPORT does not provide plug-ins. Install it, then scan it so the DAW finds it.
- Use the same format. VST2 and VST3 are separate versions of a plug-in. DAWPORT keeps the format your project used and does not swap one for the other, so install that format.
- Expect version differences. A different version of the same plug-in can behave differently.
If Live does not find an installed plug-in, Ableton has a help article on missing plug-ins.
Formats with limits
- CLAP plug-ins from an FL Studio project are not added to the Ableton Live Set, and they show as Not ported. Their identity and saved state are kept in the converted project's recovery data, but Live does not load them.
- Audio Units (Mac) in a Live Set are not placed in the FL Studio project. Their saved state is included as a separate file in the download, so the settings are not lost. Audio Units going from FL Studio to Live are experimental and have not been checked on a Mac.
- FL Studio's plug-in wrapper has its own dry/wet setting. When it is not fully wet, DAWPORT does not apply that mix in Live. The setting is kept in the converted project's recovery data, so check the plug-in's level by ear.
Stock effects become native devices
FL Studio's own plug-ins only run inside FL Studio, and Live's devices only run inside Live. So for stock effects, DAWPORT does something different: it replaces the device with the closest device in the other DAW and sets it up to match.
Converted devices keep the destination DAW's own names. A Fruity Balance becomes Live's Utility, not a device labelled "Fruity Balance", so you find it where you would expect it.
Some examples of current mappings:
| FL Studio | Ableton Live |
|---|---|
| Fruity Parametric EQ 2 | EQ Eight |
| Fruity Balance | Utility |
| Fruity Limiter | Compressor and Limiter |
| Fruity Compressor | Compressor |
| Fruity Delay 2, Fruity Delay 3 | Delay |
| Fruity Reeverb 2 | Hybrid Reverb |
| Fruity Multiband Compressor | Multiband Dynamics |
| Soundgoodizer | Audio Effect Rack with Multiband Dynamics and Limiter |
| Ableton Live | FL Studio |
|---|---|
| EQ Eight, Auto Filter | Fruity Parametric EQ 2 |
| Utility | Fruity Balance |
| Delay, Echo | Fruity Delay 3 |
| Reverb | Fruity Reeverb 2 |
| Compressor, Glue Compressor | Fruity Compressor |
| Saturator | Fruity WaveShaper |
| Multiband Dynamics | Fruity Multiband Compressor |
These mappings are approximations: they aim for the same sound, but the devices work differently inside, so the result is close rather than identical. Not every setting has a match. The conversion notes say this for each device. They name the source device and its new device, say it was converted as a close approximation that may sound slightly different, and mention when some of its settings were not carried over.
For details on each mapping, see stock effect equivalents.
Sidechain ducking
Ducking made with a keyed Fruity Limiter or a Fruity Peak Controller becomes a sidechained Compressor in Live. In the other direction, a sidechained Live Compressor becomes Fruity Compressor with the sidechain signal routed to it. Both are labelled approximations.
DAW-only instruments and effects
Each DAW's own synths are part of that DAW. DAWPORT does not try to rebuild them with a different synth.
- FL Studio: Sytrus, Harmor, FLEX, FL Keys, DirectWave and other FL Studio instruments are not converted. The one bounded exception is 3x Osc: its basic shapes (sine, triangle, square, saw, rounded saw and noise) map to Live's Operator as an approximation. FL Studio's Sampler channel becomes Live's Simpler. Gross Beat is not converted.
- Ableton Live: Operator, Wavetable and other Live synths are not converted to FL Studio. A single Simpler, and Simplers inside Instrument or Drum Racks, become FL Studio Sampler channels.
What happens to the notes of an instrument that is not converted depends on the direction:
- FL Studio to Ableton Live: the track and its notes stay in the Live Set as a MIDI track without an instrument. Load a new sound and keep going.
- Ableton Live to FL Studio: the track becomes an empty FL Studio channel with its notes. Load an FL synth or a plug-in on it. The conversion notes name the instrument, so you know which part to rebuild.
Either way, each instrument is listed as not ported.
A practical workaround: before converting, render tracks that rely on a DAW-only instrument to audio in your original DAW. The rendered audio then travels as a normal sample. See stems vs project conversion.
How to read the plug-in list
Before you convert, DAWPORT shows each device it found with an expected status: Supported, Limited, Unsupported or Pending. After the conversion, each device shows what actually happened:
- Ported: written into the new project
- Limited: converted with limits, such as an approximation or missing settings
- Not ported: could not be converted; the rest of the project still is
- Not reported: no result was reported for that device
"Ported" describes the transfer. DAWPORT cannot check playback on your computer, so open the project and listen.
Checklist before you open the converted project
- Install and scan every third-party plug-in, in the same format.
- Read the plug-in list and the conversion notes.
- Replace DAW-only instruments that were not ported.
- Compare the converted mix with your original and adjust approximated devices by ear.
Ready to convert? Go to FL Studio to Ableton Live or Ableton Live to FL Studio. For automation on plug-ins, read how automation transfers.

