When a song has to move between FL Studio and Ableton Live, there are three common ways to do it: bounce audio stems, export MIDI, or convert the whole project. None of them is always best. This page compares them so you can pick the right one, or combine them.

Convert now

2 free conversions every month. No card required.

The three options at a glance

Audio stems MIDI export Project conversion
What moves Rendered audio per track Notes only Tracks, clips, notes, mixer, devices, automation
Sounds exactly like the original Yes, it is the original sound printed to audio No, you pick new sounds Close where devices map; approximations are labelled
Editable notes No Yes Yes
Editable mixer and effects No, effects are baked in No Yes, where supported
Needs the same plug-ins No No Yes, for third-party plug-ins
Effort after moving Low to import, but limited edits High, rebuild sounds and mix Check and fix what the notes list

Audio stems

Stems are audio files, usually one per track or group, rendered from your original project.

How to export them:

Stems make sense when:

The downside: everything is baked in. You cannot change a note, swap a synth preset, or adjust a reverb that was printed into the stem. If you want to keep producing the song, stems put you back to rebuilding.

MIDI export

MIDI files carry notes, not sound.

MIDI makes sense when:

The downside: you lose the sounds, the mixer, the effects and audio clips. Rebuilding a full arrangement from MIDI takes a long time.

Full project conversion

Project conversion turns the project file itself into a project for the other DAW. DAWPORT converts FL Studio projects (.flp files) into Ableton Live Sets (.als files) and back.

Where supported, the converted project keeps:

Project conversion makes sense when:

The downside: FL Studio and Ableton Live work differently, so not everything has an exact match. Many stock device mappings are approximations. Some things are not converted, for example FL Studio's own synths beyond the basic 3x Osc shapes, Ableton's own synths, and Session View clips (DAWPORT converts the Arrangement). DAWPORT converts the rest of the project and lists what was approximated or left out in the conversion notes. You should always listen through the result and keep your original.

DAWPORT does not render audio and does not write MIDI files. If you need stems or MIDI, use your DAW's own export.

Working with someone who uses the other DAW

Project conversion is how an FL Studio producer and an Ableton Live producer can keep working on the same song. Only the person who converts needs a DAWPORT account. The other person just opens the converted project.

What the other person needs:

When the song goes back and forth:

Combining the approaches

Often the best result mixes two methods:

  1. Render the parts that will not convert. If a sound relies on an FL Studio synth or a Live device without a mapping, render that track to audio in your original DAW first. Then convert the project. The rendered audio travels as an ordinary sample, and everything else stays editable.
  2. Send or keep a bounce as well. Even after converting, a stereo bounce or a set of stems from the original is a useful reference. Compare the converted project against it and fix the differences listed in the conversion notes.
  3. Use MIDI for single ideas. For a quick loop or chord progression, a MIDI clip is still the fastest route.

How to decide

Always keep your original project. A converted project is a new copy, not a replacement.

Comparing project converters too? See FL Studio and Ableton project converters compared. Ready to try a project conversion? Go to FL Studio to Ableton Live or Ableton Live to FL Studio. If you are moving for good, read switching from FL Studio to Ableton or switching from Ableton to FL Studio.

Questions

Should I send stems or the project file?

Send stems when the other person only needs to mix, master or arrange finished sounds, especially if they do not own your plug-ins. Send a converted project when they need to keep editing notes, sounds, mixer settings and automation.

How do I export stems from FL Studio?

Export a WAV file and turn on Split mixer tracks. FL Studio then renders each mixer track to its own audio file.

How do I export stems from Ableton Live?

Use File > Export Audio/Video and set Rendered Track to All Individual Tracks. Live renders each track to its own audio file.

Does DAWPORT export MIDI or stems?

No. DAWPORT converts the project itself into an FL Studio project or an Ableton Live Set. It does not render audio or write MIDI files. Use your DAW's own export for stems or MIDI.

Does the person I send a converted project to need DAWPORT?

No. Only the person who converts needs a DAWPORT account. The other person needs the destination DAW, a Live edition that has the converted devices, and the same third-party plug-ins.

Can I send both a converted project and stems?

Yes, and it is often the safest choice. Send the converted project so the other person can keep working, plus a stereo bounce or stems from the original so they can compare.

Do the plug-ins come with a converted project?

No. The converted project keeps supported VST2 and VST3 plug-ins with their saved settings, but the plug-ins themselves must be installed on the computer that opens it.

Convert now