Switching DAWs is easier when your old songs come with you. You do not have to leave unfinished FL Studio projects behind or rebuild them from memory. This guide explains how to bring them into Ableton Live, what carries over, and what to check once a project is open in Live.

Convert now

2 free conversions every month. No card required.

Ableton Live cannot open an .flp file directly (see can Ableton open FLP files). The project has to be converted into an Ableton Live Set (.als file) first. DAWPORT does that conversion online.

Before you convert

  1. Pick a few songs first. Start with one or two projects you know well. You will quickly learn which of your usual devices convert cleanly.
  2. Gather the samples. An .flp file does not contain its samples. Put them in the project folder and upload the folder as a .zip, .rar or .7z archive. You can also upload just the .flp file, but then the converted set keeps your original sample paths. Upload limits: .flp and .als files up to 16 MB, or .zip, .rar and .7z archives up to 512 MB. See samples and missing media.
  3. Install your third-party plug-ins for Live. Use the same format (VST2 or VST3) that your FL Studio project uses.
  4. Consider rendering FL-only sounds. Sytrus, Harmor, FLEX and other FL Studio instruments are not converted. If a part depends on one, render it to audio in FL Studio before converting.
  5. Keep your original .flp. Conversion never changes your original, but keep a backup anyway.

What carries over

In FL Studio In Ableton Live
Mixer tracks your channels play through Audio tracks, MIDI tracks, Group tracks and Return tracks
Pattern clips in the Playlist MIDI clips in the Arrangement, named after the pattern
Audio clips Audio clips with warp settings, pitch, reverse, fades and gain
Notes MIDI notes with velocity
Note slides on Sampler channels and 3x Osc Per-note pitch movement
Mixer sends and routing Sends to Return tracks and track routing
Sidechain ducking with a keyed Fruity Limiter or Fruity Peak Controller A sidechained Compressor (approximation)
Tempo and tempo automation Song tempo and tempo automation
Third-party VST2/VST3 plug-ins The same plug-ins with their saved settings, where supported
Stock effects with a mapping Live's own devices, such as EQ Eight, Compressor, Limiter, Delay, Hybrid Reverb, Utility and Multiband Dynamics
3x Osc basic shapes Operator (approximation)
Sampler channels Simpler
Supported automation clips Arrangement automation
Samples from your archive A Samples/Collected folder next to the .als file

Converted devices use Ableton Live's own names, so a Fruity Balance shows up as Utility. Details: plug-ins after converting, how automation transfers and stock effect equivalents.

What works differently in Ableton Live

These differences explain why a converted project looks the way it does.

Tracks are built from your mixer

In FL Studio, Playlist tracks are not tied to an instrument or a mixer track: any clip can go on any Playlist track (Image-Line manual). In Live, a track hosts its clips and its own chain of devices, and audio clips cannot go on MIDI tracks (Ableton manual).

So DAWPORT builds Live tracks from the FL Studio mixer tracks your channels actually use, not from your Playlist rows. When several channels play through one mixer track, you get a Group track in Live with one track per channel inside it. Mixer tracks that other tracks send to in parallel, alongside their normal output, become Return tracks.

Your song lands in Arrangement View

Live has two views: Arrangement View, a timeline, and Session View, a grid for launching clips (Ableton manual). Your FL Studio Playlist arrangement becomes a timeline in Arrangement View.

Effects live on the track

FL Studio puts effects in mixer track slots. In Live, effects sit in the device chain of each track, or on Return tracks that other tracks send to. Converted effects appear in those places.

Samples belong to a Live Project

Live saves each set inside a Project folder and can collect all samples into it with Collect All and Save (Ableton manual). After opening a converted set, using Collect All and Save once is a good way to make it a normal, self-contained Live Project.

What to check after converting

Open the .als file in Ableton Live 12, then go through this list:

  1. Read the conversion notes. They list devices that were approximated or not ported, and automation that could not be converted. The plug-in list shows Ported, Limited or Not ported for each device.
  2. Missing plug-ins. If Live cannot find a plug-in, install or rescan it in the same format.
  3. Replace FL-only instruments. Tracks whose instrument was not converted keep their notes. Load a Live instrument or a plug-in and pick a sound.
  4. Listen to approximated effects. Limiter, reverb, delay and EQ mappings are approximations, not identical copies. Adjust by ear against your original.
  5. Check time-based effects. DAWPORT cannot read a sample rate from an FL Studio project, so some time-based mappings are calibrated for 48 kHz, and the notes say when that applies. If you work at another rate, listen to delays and similar effects.
  6. Check the time signature. One time signature is used for the whole song, so check songs with meter changes.
  7. Note slides. Slides on instruments other than Sampler channels and 3x Osc are left out: the notes play at their base pitch, and the conversion notes do not list these slides yet. Redraw the glide in Live if you need it.
  8. Collect All and Save once everything plays.

Learning Live with your own songs

Converting a project you already know is a good way to learn Ableton Live. You can see how your mixer turned into tracks and returns, open the converted devices to see how they are set, and compare automation lanes with your old automation clips. It is often faster than starting from a blank set.

Ready? Convert your first FL Studio project to Ableton Live. Prices and the 2 free conversions every month are on the pricing page. Going the other way? Read switching from Ableton to FL Studio.

Questions

Can I transfer my FL Studio projects to Ableton Live?

Ableton Live cannot open .flp files, but you can convert them. DAWPORT turns an FL Studio project into an Ableton Live Set with tracks, clips, notes, mixer routing, supported plug-ins and supported automation, and lists what changed.

Where do my FL Studio patterns go in Ableton?

Each pattern placed in the Playlist becomes a MIDI clip in Live's Arrangement, named after the pattern. Live tracks are built from the FL Studio mixer tracks your channels use.

Will my converted project sound the same in Ableton?

Not always. Supported third-party plug-ins carry their saved settings, but FL Studio stock effects become Ableton devices that are usually approximations, and most of FL Studio's own synths are not converted. The conversion notes tell you what differs.

Which Ableton Live version do I need?

Converted Live Sets are made for Ableton Live 12.

Should I convert all my old projects at once?

Start with one or two songs you know well, check them, and learn which of your usual devices convert cleanly. Then convert the songs you still want to finish.

Convert now