Short answer

DAWPORT converts sample playback in both directions. It carries the sample and the playing (the notes), plus the basic sample settings. Deeper sound-design settings, like filters and LFOs, are not carried.

Convert now

2 free conversions every month. No card required.

How the controls correspond

Simpler FL Sampler channel Converted?
Sample Sample Yes
Transpose / Detune Pitch / fine tune Yes
Start / End Sample start / length Yes
Reverse Reverse Yes
Volume / Pan Channel volume / pan Yes
Voices = 1, or One-Shot Cut itself Yes
Volume envelope (ADSR) Volume envelope FL → Live yes (since 1.0.70). Live → FL only in simple cases
Filter Filter No (an FL filter that is fully open is handled)
LFO LFO No
Loop, Warp, Slice modes — No
Velocity → volume Velocity Partly

Ableton to FL Studio

Simpler. Each Simpler becomes an FL Sampler channel with:

The volume envelope converts when it uses default levels with no loop and no velocity-to-time. A One-Shot gate is turned into a release.

When a Simpler uses more (filter, LFO, warp, loop or slicing), DAWPORT still converts the sample and notes as a plain Sampler channel, and reports the rest as not carried. In short, the sample and the MIDI performance transfer, but not the complete Simpler setup. A sliced Simpler, for example, is not rebuilt as slices.

Drum Rack. A Drum Rack becomes one FL Sampler channel per pad, as long as each pad holds one Simpler (or one plug-in, which becomes a plug-in channel). Every pad keeps its notes, key range and velocity range.

This is all or nothing. If even one pad does not qualify, for example because it holds another Live instrument, two instruments, or a sample that is not in your upload, the whole rack is left out: none of its pads or notes are in the FL Studio project. The conversion notes list the rack as not converted. To keep the drums, fix or remove that pad, or render the rack to audio in Live, before converting.

Not carried:

DAWPORT reports these as not carried. It does not build an FPC, FL's drum-pad plug-in.

Instrument Rack. It converts the same way when each chain is one Simpler or one plug-in, with the same all-or-nothing rule: one chain that does not qualify leaves out the whole rack. Key and velocity zones are kept. Chain-selector zones follow the selector's current position, as a fixed setting.

FL Studio to Ableton

Each FL Sampler channel becomes a Simpler with:

Sample fade-ins and fade-outs are baked into the converted sample file. Since DAWPORT 1.0.70, the volume envelope carries over to Simpler's envelope: attack, decay, sustain and release. FL's hold stage is folded in, and its delay stage is left out. Tempo-synced envelopes and the volume LFO are not carried.

In the tested default setup, a filter that is fully open (cutoff fully up, no resonance) is handled by switching Simpler's filter off. An active filter is not mapped. Velocity uses a measured curve in one supported case.

If several channels feed the same Mixer insert, each gets its own track, and the insert becomes a Group track around them. This applies to any channels sharing an insert, not only Samplers: plug-in instruments and audio clip channels too. The insert's effects sit on that Group track, so the channels still share them as in FL.

What sounds the same, and what differs

Carried over:

Can differ:

Tips after converting

  1. Drum Rack → FL: route the pad channels to Mixer inserts the way you like. Rebuild choke groups with FL's cut groups, in the channel settings.
  2. FL → Live: if a Sampler used a filter sweep, turn on Simpler's filter and set it by ear.
  3. Want a single drum instrument in FL? You can move the converted channels into FPC by hand. Converting to separate channels keeps every pad editable first.

Related

Questions

What is the FL Studio equivalent of Ableton's Simpler?

FL Studio's Sampler channel, the default channel you get when you drag a sample into the Channel Rack. Both play one sample across the keyboard with tuning, start/end and a volume envelope.

What is the FL Studio equivalent of a Drum Rack?

FL users usually build drums as one Sampler channel per sound, or use FPC. DAWPORT converts a Drum Rack to one Sampler channel per pad. It does not create an FPC.

Do drum patterns stay intact when converting a Drum Rack to FL Studio?

Yes, when every pad holds one Simpler or one plug-in. Each pad's notes go to its own channel, with its key and velocity ranges. If even one pad holds something else, the whole Drum Rack and all its notes are left out of the FL Studio project, and the conversion notes list it. Choke groups and pad sends are not carried.

What happens to FL Sampler channels in Ableton?

Each becomes a Simpler on its own MIDI track, with the sample, tuning, start and end, reverse and volume envelope. If several channels feed one Mixer insert, for example Samplers, plug-in instruments or audio clip channels, that insert becomes a Group track holding their tracks.

Convert now