FL Studio's own instruments, such as Sytrus, Harmor, FLEX, FPC and Slicex, only run inside FL Studio. Ableton Live has none of them, and DAWPORT does not swap them for a different synth. When you convert an FL Studio project to Ableton, their notes still come across: each channel becomes a Live MIDI track with its clips and notes, ready for a new sound.
2 free conversions every month. No card required.
What DAWPORT does with FL Studio synths
We converted real FL Studio projects with DAWPORT 1.1.8 to check each of these:
| FL Studio instrument | In the converted Live Set |
|---|---|
| Sytrus | Not converted. MIDI track with its notes, no instrument |
| Harmor | Not converted. MIDI track with its notes, no instrument |
| FLEX | Not converted. MIDI track with its notes, no instrument |
| FPC | Not converted. MIDI track with its notes, no instrument |
| Slicex, Fruity Slicer | Not converted. MIDI track with its notes, no instrument |
| DirectWave, FL Keys, BooBass | Not converted. MIDI track with its notes, no instrument |
| 3x Osc (basic shapes) | Converted to Operator, as a labelled approximation |
| Sampler channel | Converted to Simpler, as a labelled approximation |
For each unconverted instrument, the conversion notes say, for example: "Sytrus could not be reproduced and was not inserted. Other project content was converted." The rest of the track, including its mixer settings and supported effects, still converts. Keep your original FL Studio project: it still holds the synth's settings.
Three ways to get the sound back
1. Print it before converting. In FL Studio, render the part to audio, for example with Consolidate on the Playlist track or Render as audio clip (Image-Line manual). Put the audio clip in place of the pattern, then convert. The audio comes over to Live like any other clip. You keep the exact sound, but not the editable notes.
2. Load a Live instrument on the MIDI track. The notes are already there. Pick an instrument close to the original:
| FL Studio instrument | Live instrument to try | Live edition |
|---|---|---|
| Sytrus, Harmor | Wavetable or Operator for complex sounds, Drift for simpler ones | Wavetable and Operator: Suite. Drift: every edition |
| FLEX | Drift, or a Live preset in the sound you need | Drift: every edition |
| FPC | Drum Rack, with your drum samples on the pads | Every edition |
| Slicex, Fruity Slicer | Simpler in Slice mode, or a Drum Rack | Simpler and Drum Rack: every edition. Slicing audio to a Drum Rack: Standard or Suite |
| DirectWave | Simpler, or Sampler for multisampled instruments | Simpler: every edition. Sampler: Suite |
These are suggestions for rebuilding by hand, not DAWPORT mappings. Editions are from Ableton's edition comparison, checked on 8 November 2026.
3. Use a third-party synth in both DAWs. If the part uses a VST2 or VST3 synth such as Serum, it carries over as the same plug-in with its saved settings, as long as you install it. For future projects you plan to move, a cross-DAW plug-in keeps the sound identical.
Why DAWPORT doesn't translate synths
Every synth engine works differently inside. A Sytrus patch rebuilt in Wavetable would be a guess, and a confident-looking wrong sound is worse than a clear note telling you what to replace. DAWPORT only converts an instrument when a real-DAW check shows the result is a useful approximation. That is true today for 3x Osc with its basic shapes, and for FL Studio's Sampler channel.
Converting a project
- Convert FL Studio (.flp) to Ableton Live (.als)
- Instruments and samplers between FL Studio and Ableton
- Ableton Live synths in FL Studio, the other direction
DAWPORT is not affiliated with Image-Line or Ableton. FL Studio, Ableton Live and the device names on this page are trademarks of their respective owners.

