Short answer

3x Osc is FL Studio's simple three-oscillator synth. Ableton Live has no direct twin, but Operator can play the same basic waveforms side by side, so it is the closest match for a converted project.

Convert now

2 free conversions every month. No card required.

DAWPORT converts 3x Osc to Operator as a labelled approximation. It is the only FL synth DAWPORT converts: other FL synths are listed as not converted, with their notes kept on a MIDI track in Live. The conversion note reads: "3x Osc was converted to Operator in Ableton Live as a close approximation; it may sound slightly different."

How 3x Osc maps onto Operator

Operator is an FM synth with four oscillators (A to D) and eleven algorithms that decide which oscillators modulate which. One algorithm plays all four side by side with no FM. DAWPORT uses that one:

How the controls correspond

3x Osc Operator (converted) Notes
Sine Sine No approximation note
Triangle Triangle Approximation
Square Square 64 Harmonics above the 64th are not reproduced
Saw Saw 64 Harmonics above the 64th are not reproduced
Rounded saw Saw 64, raised 4.62 dB to match loudness Operator has no rounded saw; the lowest harmonics differ by up to about 8 dB
Noise Operator noise, in a left/right Instrument Rack Operator's noise is the same on both sides, FL's isn't, so DAWPORT plays two copies panned left and right
Custom sample shape — Not converted
OSC 2 and OSC 3 level knobs Oscillator levels FL's level mix, measured against renders
Coarse pitch (and 3x Osc's octave) Coarse ratio and Fine Converted from semitones to Operator's frequency ratio plus fine tuning
Fine pitch Fine Converted to Operator's fine-tuning scale
Stereo phase offset, stereo detune — Not reproduced, and named in the notes
Channel volume envelope Operator's amplitude envelope Attack, decay, sustain and release
Channel volume and pan Utility after Operator FL's channel volume law
Pitch slides in the notes Per-note pitch in Live Carried on the same channel

Levels were matched in real Live and FL Studio renders. Triangle, Square 64 and Saw 64 match FL's level at the sine volume, and the rounded saw needs the 4.62 dB lift shown above. A 3 dB level error in the channel volume was fixed in DAWPORT 1.0.70, and the fix was confirmed on held-out FL volumes.

What DAWPORT does with 3x Osc

Converted (approximation). Since DAWPORT 1.0.70, a 3x Osc with sine, triangle, square, saw, rounded saw or noise oscillators converts. Before 1.0.70, only sine and noise did. The notes list each approximation, such as "saw as Operator Saw 64 (harmonics above the 64th are not reproduced)".

The volume envelope carries over as attack, decay, sustain and release. FL's hold stage is folded into the decay, and its delay stage and curve shapes are not carried. A tempo-synced envelope falls back to a plain on/off shape.

Not converted, listed in the notes, with the notes kept on a MIDI track and the settings kept in the recovery data:

A silent oscillator (level at zero) doesn't count. It can use any shape.

Not carried at all: the channel's filter, mono and glide (porta) settings. Operator uses up to 32 voices.

What sounds the same, and what differs

Close:

Can differ:

Operator in FL Studio (the other direction)

DAWPORT doesn't convert Live synths, Operator included, to FL Studio. Going from Ableton to FL Studio, a track with Operator is listed as not converted and becomes an empty FL Studio channel with its notes, ready for an FL synth such as 3x Osc. Render that track to audio in Live before converting if you need the exact sound. See Ableton synths in FL Studio.

Tips for matching by hand

  1. In Operator, pick the algorithm with all four oscillators side by side (no FM), and turn off D.
  2. Set each oscillator's waveform and level to match 3x Osc.
  3. Operator's Coarse is a frequency ratio, not semitones: 1 is the base pitch and 2 is one octave up. Set octaves with Coarse and smaller steps with Fine.
  4. For FL's stereo detune, put Operator in an Instrument Rack with two chains panned left and right, and detune one chain slightly.
  5. Turn on Operator's filter only if your FL channel used its filter.

Related

Questions

What is the Ableton equivalent of 3x Osc?

Live has no three-oscillator synth that works like 3x Osc. Operator comes closest for a converted project: it has four oscillators with sine, saw, square, triangle and noise waveforms, and can mix them in parallel. DAWPORT converts 3x Osc to Operator as a labelled approximation.

Which 3x Osc settings carry over to Operator?

The sine, triangle, square, saw, rounded saw and noise shapes, the oscillator levels, coarse and fine tuning, and the channel's volume envelope. Pitch slides in your notes become per-note pitch in Live. The custom sample shape, oscillator panning, phase inversion, phase randomness and Osc 3 amplitude modulation keep a 3x Osc from converting.

Does DAWPORT convert other FL synths like Sytrus or Harmor?

No. 3x Osc is the one FL synth DAWPORT converts. Other FL synths are listed as not converted, and their notes stay on a MIDI track in Live. See FL Studio synths in Ableton.

Does Operator convert to 3x Osc in FL Studio?

No. Going from Ableton to FL Studio, Live synths such as Operator are not converted. The track becomes an empty FL Studio channel with its notes, ready for an FL synth. Render the part to audio in Live first if you need the exact sound.

Does every Ableton Live edition have Operator?

No. Operator is included in Live Suite only, not in Live Intro or Standard, according to Ableton's edition comparison. Open a converted Set that uses Operator in Live Suite.

Convert now