Short answer

An Audio Effect Rack in Ableton Live holds effects in one or more chains. With several chains, the sound is split, processed in parallel and mixed back together. Racks also have macro knobs and a chain selector.

Convert now

2 free conversions every month. No card required.

FL Studio has no rack device. The closest native tools are:

DAWPORT uses whichever fits. A simple one-chain rack becomes effects in a row on the track's Mixer insert. A rack with parallel chains becomes one Patcher, in DAWPORT's standard conversion.

One chain: effects in a row

A rack with a single chain, at 0 dB and centred, with nothing at rack or chain level automated, is just a container. DAWPORT places its devices in order on the track's Mixer insert, each converted on its own. A one-chain rack holding just a Utility goes straight onto the Mixer track.

Parallel chains: one Patcher

Since DAWPORT 1.0.70, a rack with parallel chains is rebuilt as a single Patcher in one Mixer slot. The conversion note reads: "Audio Effect Rack rebuilt as one FL Studio Patcher: each chain becomes a parallel path of FL devices mixed together at the output, keeping each chain's volume and pan."

Rack feature FL Studio (converted) Notes
Chains Parallel paths inside the Patcher Mixed back together at the output
Device order in a chain Same order in that path Each device converts on its own terms
Chain volume and pan Link levels in the Patcher Live's equal-power pan law is applied; uneven left/right levels use Fruity Stereo Shaper nodes that pass one channel
Device Dry/Wet A dry and wet blend in the Patcher For values between dry and fully wet
Muted, soloed-out or −inf dB chains Left out They are silent in Live, so the sound doesn't change
Chain selector position Fixed chain levels The selector itself is not recreated
Macro positions Applied to the settings they control The macro knobs are not recreated
Nested racks Nested parallel paths in the same Patcher Bypassed nested racks and devices are left out
Chain names — Not carried

The Patcher can hold up to 256 nodes, and racks nested up to 8 levels deep.

What can go inside a rebuilt rack

A device can go into the Patcher when it converts to a complete FL plug-in on its own. A few kinds can't, and stop the rack from being rebuilt:

The whole rack, or none of it

A rack is rebuilt as a whole or not at all. Mixing some converted chains with gaps would change the balance between them. DAWPORT leaves the whole rack out when:

The note says the rack "could not be rebuilt as an FL Patcher", gives the reason, and the devices stay in the conversion's recovery data. The rest of the project still converts.

Automation inside the Patcher is not carried. The note says the device "keeps its current setting".

Macro automation (since 1.0.72)

Live users often automate a macro instead of the device it controls. Since DAWPORT 1.0.72, an automated macro in an Audio Effect Rack can be turned into automation of the control it drives, using Live's measured macro mapping. This works for:

The macro needs a single automation lane and its full range, with no modulation, and the driven control must not be automated already. The note then says the macro's automation "now moves the control it drives". Macro automation of other controls is not carried.

The new automation plays in FL Studio when the driven device sits directly on a Mixer insert, as in a one-chain rack. Inside a rebuilt Patcher, device automation is not carried.

Tips for building a rack by hand in FL Studio

  1. For parallel processing, open Patcher on the Mixer insert, add one path per chain, and connect them all to the output.
  2. Or route the track to two or more Mixer tracks, process each, and send them on to one bus.
  3. To mimic a macro, link several knobs to one controller, or automate each control directly.
  4. Check levels after summing. Parallel paths add up, so start each one a few dB lower.

The other direction

Going from FL Studio to Ableton, DAWPORT often builds Audio Effect Racks itself, for example for Soundgoodizer, Fruity Delay 3 and Fruity Reeverb 2, to keep FL's separate dry and wet levels. See the device equivalents table for the full list.

Related

Questions

What is the FL Studio equivalent of an Ableton Audio Effect Rack?

For a rack with one chain, simply the same effects in a row on a Mixer insert. For parallel chains, Patcher, FL Studio's built-in plug-in host, where you can split a signal into parallel paths of plug-ins and mix them back together. DAWPORT uses both, depending on the rack.

Do rack macros convert to FL Studio?

FL Studio has no macro knobs for a converted rack, so the macros themselves are not recreated. Their current positions are applied to the settings they control. Since DAWPORT 1.0.72, an automated macro that drives Utility Gain, Utility Balance, Reverb Dry/Wet or an on/off switch becomes automation of that control, in supported cases.

Why was my whole rack left out?

A rack is rebuilt as a whole or not at all. If one active device inside it can't be converted to FL Studio, or the rack uses return chains, chain sends or automated chain controls, DAWPORT leaves the whole rack out. The notes give the reason and the rest of the project still converts.

Do Instrument Racks and Drum Racks work the same way?

No. They are converted as instruments, with one FL channel per chain or pad in supported cases. See the Simpler and Drum Rack page for details.

Convert now