Short answer

FL Studio has no single plug-in that does everything Ableton's Utility does. The closest native tools are:

Convert now

2 free conversions every month. No card required.

When DAWPORT converts a Live Set to FL Studio, each Utility becomes one of these, or both in a row. The FL devices keep their own FL names.

How the controls correspond

Utility control FL Studio equivalent DAWPORT conversion
Gain Fruity Balance volume Plain static gain from −35 to +5 dB, set to within 0.01 dB
Mute, or Gain at −inf Silence Converted
Width (incl. 0% = mono) Fruity Stereo Shaper Converted when FL can reproduce the same stereo mix
Mono switch Fruity Stereo Shaper Converted
Mid/Side mode Fruity Stereo Shaper Converted when it can be reproduced
Channel mode Left / Right / Swap Fruity Stereo Shaper Converted
Phase invert L / R Fruity Stereo Shaper Converted
Balance Left and right levels At the default 100 percent width only; an approximation in some cases
Bass Mono — Not converted
DC filter — Not converted
Gain automation Fruity Stereo Shaper slot mix automation Turn-downs only (see below)

How does it work? DAWPORT treats a Utility as two parts: a fixed stereo mix (how much of the left and right inputs ends up in each output) and a gain. The stereo mix goes to Fruity Stereo Shaper, which can express many of the same mixes. The gain goes to Fruity Balance. If FL can't reproduce the stereo mix, it is reported instead of being guessed. The gain part can still convert on its own.

What DAWPORT does with Utility

Plain gain. A Utility that only changes volume becomes a Fruity Balance. The resulting level must land within 0.01 dB of Live's, or the Utility is reported instead.

Width, mono, channel or phase changes. These become a Fruity Stereo Shaper. Width and gain together become a Fruity Stereo Shaper followed by a Fruity Balance (for gains from −20 to +5 dB).

Gain automation. Utility gain automation is very common in Live for fades, volume rides and pumping. It converts when:

It is rebuilt as automation of a Fruity Stereo Shaper's Mixer slot mix knob. The notes call it an approximation: the curve follows a 1/16-beat grid, and below about −35 dB the gain law is approximate. Clip envelopes and gain boosts in the automation are not converted this way.

Rack macros (since 1.0.72). If Utility sits in an Audio Effect Rack and an automated macro turns only its Gain, DAWPORT turns the macro automation into Gain automation. The rules above then apply. A macro that also drives other controls is left as it is and reported.

Shaper pumping. A supported Max for Live Shaper modulating Utility Gain becomes FL mixer volume automation, labelled as an approximation. This is a common way to make beat-synced pumping in Live.

Not converted:

These are listed in the conversion notes, and the rest of the project still converts.

What sounds the same, and what differs

Very close:

Can differ slightly:

Tips for doing it by hand in FL Studio

  1. Use Fruity Balance for clean gain staging, the way you used Utility in Live.
  2. Use Fruity Stereo Shaper for width and mono checks. Sending left and right equally to both outputs gives you mono.
  3. For mono bass, which Utility does with Bass Mono, split the low end with an EQ or a multiband setup and make only that part mono.
  4. For volume rides, automating the Mixer track volume or a Fruity Balance volume is the FL habit.

Related

Questions

What is the FL Studio equivalent of Ableton Utility?

For gain, Fruity Balance. For width, mono, channel swap and phase invert, Fruity Stereo Shaper. Utility does both jobs in one device; in FL you may need both plug-ins.

Does Utility gain automation carry over to FL Studio?

Yes, when the Utility only changes gain, and the automation only turns the sound down (0 dB or below) in a single Arrangement automation lane. DAWPORT builds it as automation of a Fruity Stereo Shaper's Mixer slot mix knob, labelled as an approximation.

Does Bass Mono convert?

No. Utility's Bass Mono and DC filter have no direct FL stock equivalent in DAWPORT's mappings, so a Utility using them is reported and left out.

What about Utility inside a rack with a macro?

Since DAWPORT 1.0.72, an automated rack macro that drives only Utility Gain is turned into automation of that Gain. It then carries over to FL Studio under the same rules as other Utility gain automation.

Convert now