Short answer

FL Studio has two stock stereo tools that Ableton Live doesn't have as such:

Convert now

2 free conversions every month. No card required.

Live's Utility covers width, mono, a single channel and phase invert, but not a free channel mix or a channel delay. So DAWPORT rebuilds both FL devices as an Audio Effect Rack whose chains each hold one Utility. When the FL device delays one channel, Live's Align Delay is added before or after the rack, in the same order as in FL.

How the controls correspond

Fruity Stereo Shaper

Stereo Shaper Ableton Live (converted) Notes
Left to left, right to left, left to right, right to right Rack chains, each a Utility set to Left or Right, with chain volume and pan Measured FL knob law
Negative amounts (phase-inverted blend) Utility phase invert on that chain Carried
Delay (one channel) Align Delay on that channel Up to FL's full 500 ms range
Pre / post order of delay and mix Align Delay before or after the rack Carried
Phase offset — Left out when a delay is also used; otherwise the device is not converted
In/Out difference output — Not converted
Mixer slot mix knob Dry chains in the rack Only without a delay; with a delay the knob must be fully up

Fruity Stereo Enhancer

Stereo Enhancer Ableton Live (converted) Notes
Volume Chain levels Fruity Balance volume law
Pan Chain levels Turns one side down, as FL does
Stereo separation Chain levels and cross-feed Measured FL law
Phase inversion (left or right) Utility phase invert Carried
Phase offset (a delay on one channel) Align Delay on that channel Up to FL's full range
Pre / post Align Delay before or after the rack Carried
Mixer slot mix knob Dry chains in the rack Only without a phase offset; with one the knob must be fully up

Why a rack? Each Utility passes one input channel, and the chain's volume and pan send it to the left output, the right output or both. Live's chain pan uses an equal-power law, and DAWPORT sets each chain's volume and pan from that law, so the chains add up to the FL mix.

What DAWPORT does

Converted. A Stereo Shaper or Stereo Enhancer with static settings becomes the rack above, with Live's own device names: Audio Effect Rack, Utility and, where needed, Align Delay. After writing the Set, DAWPORT reads the rack back and checks that the channel mix and delay match the plan.

Phase offset (Stereo Shaper). Live has no stock device that shifts one channel's phase like this. Since DAWPORT 1.0.70, when a Stereo Shaper uses both a delay and a phase offset, it converts the channel mix and the delay and leaves the phase offset out. The note says the phase offset "has no Ableton Live equivalent and is left out", that each channel sounds the same on its own, but the stereo image in the low and mid range is narrower and mono playback can differ. It suggests widening the track with Utility's Width if it sounds narrower. A Stereo Shaper that uses phase offset without a delay is not converted.

Volume-only Stereo Shaper. A Stereo Shaper with all mix knobs at zero, used only to turn a track down through its automated Mixer slot mix knob, becomes a single Utility with gain automation.

Not converted, listed in the notes and kept in the recovery data:

Automation of a Stereo Enhancer is not carried. The rest of the project still converts.

How close it is

It is a rebuild from measured laws, not FL's own plug-in, so check the stereo image by ear, and in mono.

Ableton Utility in FL Studio (the other direction)

Going from Live to FL Studio, Live's Utility becomes Fruity Balance for gain and Fruity Stereo Shaper for width, mono, channel and phase changes. See Ableton Utility in FL Studio.

Tips for matching by hand

  1. For a plain width or mono change, a single Utility is enough. Use Width, Mono and the channel mode.
  2. For an FL-style blend (for example, some of the left channel in the right), build an Audio Effect Rack with one chain per input channel, a Utility set to Left or Right in each, and pan the chains.
  3. For the Haas-style delay of a Stereo Enhancer, use Align Delay with Link off and delay one side by the same milliseconds.
  4. Always check the result in mono. Delayed and phase-inverted blends can cancel.

Related

Questions

What is the Ableton equivalent of Fruity Stereo Shaper?

There is no single one. Live's Utility handles width, mono, channel selection and phase invert, but it can't mix one channel into the other at a chosen level or delay one side. DAWPORT rebuilds a Stereo Shaper as an Audio Effect Rack of Utility devices, plus Align Delay when a channel delay is used.

What is the Ableton equivalent of Fruity Stereo Enhancer?

The same rebuild. Its volume, pan, stereo separation and phase inversion become a rack of Utility devices, and its phase offset (a short delay on one channel) becomes Align Delay.

Does the Stereo Shaper phase offset convert?

No. Live has no stock device that shifts the phase of one channel the way Stereo Shaper does. When a Stereo Shaper also uses a channel delay, DAWPORT converts the mix and the delay and leaves the phase offset out, with a note. A Stereo Shaper that uses phase offset without a delay is not converted.

Does Stereo Shaper automation carry over to Ableton?

Generally no. An automated Stereo Shaper is left out and reported. The exception is a Stereo Shaper whose only job is a volume move through its automated Mixer slot mix knob: that becomes a Utility with gain automation.

Convert now