Short answer
Ableton Live has no Soundgoodizer. The closest native setup is an Audio Effect Rack with two chains: a clean Dry chain and a Wet chain with Multiband Dynamics followed by Limiter. Soundgoodizer's Amount knob is the blend between the two.
2 free conversions every month. No card required.
That is also what DAWPORT builds when it converts an FL Studio project that uses Soundgoodizer. The result is labelled as an approximation, not as an exact copy.
What Soundgoodizer actually does
Soundgoodizer has two controls: a preset (A, B, C or D) and Amount. In DAWPORT's FL Studio test renders, it behaved like this:
- the dry signal times (1 − Amount), plus
- Amount times a fixed three-band maximizer, which is different for each preset.
Each preset splits the sound into low, mid and high bands. It pushes each band up hard into a fast, very high-ratio stage, then caps the result just under 0 dBFS. That is why it makes things louder and brighter so quickly.
The Live equivalent, control by control
| Soundgoodizer | Ableton Live (converted) |
|---|---|
| Preset A / B / C / D | Fixed settings in the Wet chain's Multiband Dynamics and Limiter, one set per preset |
| Amount | Chain volumes: Wet = Amount, Dry = 1 − Amount (with a small fixed trim) |
| The band split | Multiband Dynamics crossover points |
| The final ceiling | Limiter ceiling, about −0.2 dB |
| Mixer slot mix knob | Must be fully up to convert (see below) |
Here are the crossover points DAWPORT uses for each preset. They come from FL renders:
| Preset | Low / mid split | Mid / high split |
|---|---|---|
| A | about 210 Hz | about 3.4 kHz |
| B | about 95 Hz | about 2.0 kHz |
| C | about 410 Hz | about 4.3 kHz |
| D | about 123 Hz | about 3.0 kHz |
The Dry chain holds a Multiband Dynamics with every band switched off. It doesn't compress anything. It is there because a band split shifts the phase slightly, and FL's Soundgoodizer has that phase shift even at Amount 0. Keeping it in both chains stops the two chains from fighting each other when they are blended.
What DAWPORT does with Soundgoodizer
DAWPORT 1.0.72 added the Soundgoodizer conversion for FL Studio to Ableton projects. It works like this:
- Converted (approximation): the Mixer slot's mix knob is fully up, nothing is sidechained into that insert, and neither Soundgoodizer nor its slot is automated. You get the Dry/Wet rack described above, using Live's own device names.
- Slot mix at 0%: the effect is silent in FL, so you get a neutral Utility.
- Not converted: a slot mix knob set between zero and full, a sidechain into the insert, or automation. In these cases no Live device is added. The original Soundgoodizer settings are kept in the conversion's recovery data, and the conversion notes list it as not converted.
In real FL Studio and Live renders of real project settings, the level on drums and full mixes differed by about 0.4 to 0.9 dB on average. The conversion notes say: "Loudness and brightness are close; peaks and pumping can differ slightly." Live's Multiband Dynamics and Limiter replace FL's own maximizer, so the band edges and how it reacts to sharp peaks are not identical.
The same release took the number of converted Soundgoodizers in DAWPORT's test projects from 0 to 85.
What sounds the same, and what differs
Close: overall loudness, the brighter, denser tone, and the balance between low, mid and high bands at your Amount setting.
Can differ slightly:
- how fast peaks are caught
- pumping on dense drum loops
- where exactly the bands meet
If a converted mix bus sounds a little more or less squashed than in FL, this device is a good place to check.
Tips for matching Soundgoodizer by hand in Live
- Create an Audio Effect Rack with two chains. Name them Dry and Wet.
- On the Wet chain, add Multiband Dynamics. Set high input gain on each band, a high ratio above the threshold, a fast attack and a short release. Then add Limiter with a ceiling just under 0 dB.
- On the Dry chain, you can add a Multiband Dynamics with all bands off. It keeps the phase in line with the Wet chain.
- Map both chain volumes to one macro, Wet going up and Dry going down. That gives you a single Amount knob back.
- Match by ear at the same loudness. A louder version always sounds "better" at first.
Related
- Fruity Multiband Compressor in Ableton: the same Live device used as a regular multiband compressor
- Fruity Limiter in Ableton
- All device equivalents
- Convert an FL Studio project to Ableton

