Short answer
Fruity Limiter is three tools in one: a limiter, a compressor and a noise gate. In Ableton Live they are three separate devices:
2 free conversions every month. No card required.
- LIMIT section → Limiter
- COMP section → Compressor
- NOISE GATE section → Gate
When DAWPORT converts an FL Studio project, Fruity Limiter becomes a Live Limiter. If its compressor section is doing something, it becomes a Compressor followed by a Limiter. Both are labelled as approximations in the conversion notes.
One thing most people don't know
The LIMIT / COMP / NOISE GATE buttons only change which panel you see. In DAWPORT's FL Studio test renders, all sections stayed active whatever panel was on screen. A compressor you set up and then "left" by switching to LIMIT is still compressing.
So DAWPORT reads every section's settings and ignores which panel is showing.
How the controls correspond
| Fruity Limiter | Ableton Live | How DAWPORT carries it |
|---|---|---|
| LIMIT: Gain | Limiter Gain (or Compressor output gain when a compressor stage is added) | Measured FL gain curve, converted to dB |
| LIMIT: Ceiling | Limiter Ceiling | Measured FL ceiling curve |
| LIMIT: Release, Sustain, release curve | Limiter Release | Measured timing law, up to 3000 ms |
| LIMIT: Attack | Limiter Lookahead | 3 ms, or 6 ms for slow FL attacks |
| COMP: Threshold | Compressor Threshold | Measured law, nudged by the Sustain setting |
| COMP: Ratio and Knee | Compressor Ratio, Knee 3 dB | Measured ratio law; FL's knee steepens the ratio |
| COMP: Attack / Release | Compressor Attack / Release | Measured timing tables |
| Sidechain input (another insert) | Compressor sidechain from that track | See the next section |
| Saturation | — | Must be at its default to convert |
| NOISE GATE | — | Not converted (see below) |
The values are converted through curves measured from real FL Studio renders, instead of copying knob positions. A 50% knob in FL doesn't mean the same thing as a 50% knob in Live.
Sidechain: Fruity Limiter keyed from another track
This is the classic FL sidechain: a kick insert routed into a bass insert as a sidechain, with Fruity Limiter on the bass in COMP mode.
Since DAWPORT 1.0.72, when the compressor section is in use, this becomes:
- a Live Compressor whose sidechain listens to the kick track at Post FX, with the kick's fader level set as the sidechain gain
- then the Limiter, which still listens to its own track, just like in FL
Only the compressor section listens to the sidechain. DAWPORT's FL Studio renders showed the same thing in FL. If only the limiter section is in use, the sidechain has nothing to drive, so you get just the Limiter.
The conversion notes say which track triggers the ducking. In real Live renders of the converted sets, the ducking was usually within about 0.1 to 0.4 dB of FL on average, and up to about 1 dB at the deepest point of each duck.
Very deep or slow-releasing ducking can differ by about 1 to 2 dB on average, and the notes tell you when that applies. If the sidechain sound is wide or only in one speaker, Live ducks a little less.
The sidechain is not rebuilt when the source track:
- is missing from the Set or is the same track
- is muted
- has automated volume
- would create a feedback loop
In those cases DAWPORT leaves that Fruity Limiter out, and its settings stay in the conversion's recovery data.
For sidechain made with Fruity Peak Controller instead, see Fruity Peak Controller in Ableton.
How close it sounds
These numbers come from rendering the same settings in real FL Studio and real Live:
- Limiter: within about 0.01 dB on steady tones, and 0.02 to 0.15 dB on drums and mixes. Very loud drums driven hard into the limiter differed by about 0.4 to 0.8 dB.
- Compressor section: about 0.1 dB on steady tones, and 0.1 to 0.9 dB on drums and mixes.
Without a sidechain, the notes say: "Limiting/compression is present; transient punch and release can differ slightly."
What DAWPORT does not convert
DAWPORT leaves a Fruity Limiter out (keeping its settings in the recovery data, and listing it as not converted in the notes) when any of these apply:
- Its controls are automated.
- The Mixer slot's mix knob is not fully up.
- The noise gate is active. Live's Gate reacts to a smoothed level, while FL's gate reacts to peaks. In real Live tests, the best mapping still differed by about 0.7 to 1.8 dB on average on real project settings, and more on drums hovering near the threshold. So DAWPORT doesn't convert it.
- Saturation is moved from its default.
- A setting is outside the measured range, for example the highest compressor ratios, or very long release and sustain settings.
Ableton Limiter in FL Studio (the other direction)
Converting from Live to FL, Live's Limiter becomes Fruity Balance → Fruity Limiter:
- Live's Gain → Fruity Balance volume, within 0.05 dB
- Live's Ceiling → Fruity Limiter ceiling, through a measured law. This is not true-peak limiting, so short peaks can go over it.
- Maximize mode is handled from its threshold and output settings
- Soft Clip and True Peak modes, and Mid/Side routing, are approximated with FL's normal stereo limiter
Lookahead and auto release are not carried. Release is carried only in one narrow measured case (a standard 100 ms release); otherwise it is left out too. An automated Limiter is not converted.
FL's ceiling law was measured at 48 kHz. Live Sets usually don't store their sample rate, so DAWPORT assumes 48 kHz and says so in the report.
Tips for matching by hand
- In FL, check all three panels before you judge the sound. Another section may be active.
- In Live, put the Compressor before the Limiter, the same order FL uses inside one plug-in.
- Use Live's Limiter Lookahead at 3 ms as a starting point for FL's default attack.
- For sidechain, route the kick into Compressor's sidechain at Post FX and set the sidechain gain to match the kick's fader.

