Short answer
Fruity Compressor (FL Studio) and Compressor (Ableton Live) are each other's closest native match. Both give you threshold, ratio, knee, attack, release and output gain.
2 free conversions every month. No card required.
DAWPORT converts in both directions, as labelled approximations:
- Live → FL: Compressor in Peak mode with the Log envelope becomes Fruity Compressor. Sidechain from another track converts too, in supported cases.
- FL → Live: Fruity Compressor becomes Compressor, within a measured range of settings.
Why you can't just copy the numbers
The same numbers don't sound the same. In DAWPORT's measurements of both devices:
- Release: Fruity Compressor needs about three times Live's value for a similar recovery.
- Attack: Fruity Compressor needs a longer attack too.
- Detection: Live's Compressor reacts to the average of both stereo channels. Fruity Compressor reacts to the louder one. So on wide stereo material, FL compresses about 1 to 2 dB more at the same settings.
DAWPORT converts every control into real units (dB, ms, ratio) and then applies these measured laws. It never copies knob positions.
How the controls correspond
| Live Compressor | Fruity Compressor | Live → FL (DAWPORT) |
|---|---|---|
| Threshold | Threshold | In dB, raised by up to 1 dB to react like Live on music |
| Ratio | Ratio | Same ratio |
| Attack | Attack | 1.6 × Live's attack + 1 ms |
| Release | Release | 3.1 × Live's release |
| Knee | Type (hard / medium / soft) | Nearest knee type |
| Output gain | Gain | In dB |
| Sidechain EQ high-pass (up to 100 Hz) | — | Becomes a small threshold lift (up to 2.5 dB); rebuilt on the helper track for an external sidechain |
| Lookahead | — | Not carried (noted), except on the sidechain path |
| Sidechain from another track | Sidechain input | Through a "Sidechain detector" helper track |
When the attack is close to the release, DAWPORT also applies a measured correction. That case over-compressed in tests.
If a track has several compressors in a row, they all convert. In DAWPORT's tests with real Live renders, a stack was about as accurate as its least accurate single compressor; the error did not add up.
Ableton Compressor to FL Studio: what converts
A Live Compressor in Peak mode with the Log envelope converts to Fruity Compressor. A Compressor that uses any of these is left out and reported, and the rest of your project still converts:
- RMS or Expand mode, or the Lin envelope
- auto release, or auto makeup
- Dry/Wet not fully wet
- automation of the compressor
- a sidechain EQ other than a high-pass, or a high-pass above 100 Hz
The conversion notes say the level typically differed by 0.1 to 0.7 dB in tests with real FL Studio renders. Slow attacks on sustained sounds and very heavy compression can differ more.
Sidechain compression (Live → FL)
A Live Compressor whose sidechain listens to another track (a kick ducking a bass, for example) becomes a Fruity Compressor whose sidechain input comes from a helper Mixer track named Sidechain detector. That helper is fed by the key track, so the ducking follows the real kick, at the same level Live heard.
A sidechain high-pass is rebuilt on the helper track. Lookahead of 1 or 10 ms is reproduced by playing the helper track early through FL's delay compensation (measured at 1 ms).
This path covers a compressor that sits directly on the track (not inside a rack), fully wet, with the sidechain mix fully up, with no automation on the compressor or the key track's output. The key track must be unmuted and not panned. Other cases are reported and left out.
The conversion notes add two caveats:
- A wide stereo key ducks somewhat more in FL. Mono keys, like most kicks, behave the same.
- With long releases, FL recovers faster after deep ducking, so the duck is shallower between hits.
Fruity Compressor to Ableton: what converts
Going from FL to Live, DAWPORT only converts Fruity Compressors inside the range where real FL Studio and Live renders were checked:
| Control | Range that converts |
|---|---|
| Threshold | −27 to −14 dB |
| Ratio | 2.5:1 to 8:1 |
| Attack | 2 to 15 ms |
| Release | 75 to 1500 ms |
| Type | Hard, medium or soft knee |
Live's Compressor is set to Peak mode with the Log envelope, no lookahead, and auto release and makeup off. Threshold, ratio, knee and output gain carry over. Attack and release use measured timings.
The notes say the level differed by up to about 0.6 dB while compressing, and up to about 4 dB on brief transients.
For a converted Fruity Compressor, the notes say the original settings are kept in the conversion's recovery data. Its latency setting is not carried.
A Fruity Compressor is left out and reported, and the rest of the project still converts, when it uses:
- the Vintage knee type, or TCR (transient-controlled release)
- expansion
- a sidechain input
- automation
- a Mixer slot mix turned down from full
- settings outside the range in the table above
Tips for matching by hand
- Match the threshold first, using gain reduction meters on a loop.
- Moving Live → FL, start with a release about 3 times longer. Moving FL → Live, start shorter, then adjust by ear.
- On wide stereo buses, expect FL to squeeze a bit more. Try raising its threshold 1 to 2 dB.
- Compare at the same output loudness, not the same knob positions.
Related
- Glue Compressor in FL Studio
- Fruity Limiter in Ableton: FL's other compressor, including its sidechain
- All device equivalents

