Short answer

FL Studio doesn't have a Glue Compressor. The closest native device is Fruity Compressor. Its plain ratio, threshold and timing controls can get near Glue's bus-compressor feel, but only if you translate the settings. Copying the numbers doesn't work.

Convert now

2 free conversions every month. No card required.

When DAWPORT converts an Ableton Live Set to FL Studio, each Glue Compressor becomes a Fruity Compressor. The settings come from a measured matching curve, and the conversion notes label it as an approximation.

Why Glue needs translating

Glue Compressor is modelled on a classic console bus compressor. It has only three ratios (2, 4 and 10), a set of fixed attack and release steps, an Auto release, a Range control and a soft clipper.

In DAWPORT's measurements, Glue's ratios didn't behave like the same ratio on a plain compressor:

Glue ratio Effective ratio in Fruity Compressor Threshold shift Knee (Fruity Compressor type)
2:1 about 3:1 about 2.9 dB lower very wide (Soft)
4:1 4:1 about 0.6 dB higher narrow (Hard)
10:1 about 10.9:1 about 3.8 dB higher narrow (Medium)

This is why "set Fruity Compressor to 2:1" sounds lighter than Glue at 2:1. Glue's 2:1 has a very wide, soft knee and starts working earlier.

How the controls correspond

Glue Compressor Fruity Compressor in FL Studio Notes
Threshold Threshold Shifted per ratio (table above)
Ratio 2 / 4 / 10 Ratio and knee type Measured effective ratio
Attack Attack Measured Glue timing law
Release Release Measured Glue timing law
Release: Auto Release (one fixed value) 400 ms at 2:1, 1000 ms at 4:1, 2000 ms at 10:1
Makeup Gain (output) In dB
Dry/Wet Mixer slot mix knob So the blend still works
Range — Not carried; a range under 20 dB is not converted
Soft clip — Not carried (it only affects peaks near full scale)
Oversampling — Not carried
Sidechain — Not converted

The Auto release

Glue's Auto release adapts to the music. Fruity Compressor has one fixed release, so DAWPORT picks a fixed value that matched real Live renders best at each ratio.

The 4:1 value (1000 ms) was confirmed in DAWPORT 1.0.72 on fresh test material: vocals, bass, kick and bass, and a mix. It improved every tested case over the earlier value. Measured against real Live, Auto release averaged about 1.1 dB of difference, and up to about 2.4 dB on busy drums with a fast attack.

What DAWPORT does with Glue Compressor

Ableton → FL Studio. The Glue Compressor converts to a Fruity Compressor unless one of these applies:

In those cases the Glue Compressor is reported and left out. The rest of the project still converts.

Range (when 20 dB or more but not at its −70 dB default), soft clip and oversampling don't stop the conversion. The notes just say they were not carried.

One older, narrowly measured setting (4:1, 30 ms attack, 600 ms release, threshold between −35 and −15 dB, default Range, no soft clip or oversampling) has its own path. On that path, makeup gain is rebuilt with Fruity Balance after the compressor.

The notes say the level typically differed by 0.1 to 0.8 dB in tests, and that it is not identical to Glue Compressor.

Several Glues and Compressors in a row on one track all convert. In DAWPORT's tests with real Live renders, a stack was about as accurate as its least accurate single device, so the error did not add up.

FL Studio → Ableton is different. DAWPORT never creates a Glue Compressor. FL's compressors become Live's Compressor, Limiter or Multiband Dynamics (see Fruity Compressor in Ableton).

Tips for recreating Glue by hand in FL Studio

  1. On the mix bus, start with Fruity Compressor at about 3:1 with a soft knee to imitate Glue's 2:1.
  2. For Glue's "30 ms attack, Auto release" at 4:1, DAWPORT's measured law lands near a 100 ms attack and a 930 ms release in Fruity Compressor. Fruity Compressor needs a longer attack than the Glue number suggests.
  3. Use the Mixer slot's mix knob for parallel compression, like Glue's Dry/Wet.
  4. Aim for the same 1 to 3 dB of gain reduction on the meters, rather than matching the threshold number.
  5. If you used Glue's soft clip to shave peaks, add a gentle clipper or limiter after the compressor.

Related

Questions

Is there a Glue Compressor in FL Studio?

No. Glue Compressor is an Ableton Live device. The closest native FL Studio device is Fruity Compressor, set up with the right ratio, threshold and timing.

How does DAWPORT convert Glue Compressor to FL Studio?

It becomes a Fruity Compressor with settings from a curve measured against real Glue Compressor renders in Live. Makeup becomes the compressor's output gain, and Dry/Wet becomes the Mixer slot's mix knob. It is labelled as an approximation.

What happens to Glue's Auto release?

Fruity Compressor has one fixed release, so DAWPORT uses a measured fixed value: 400 ms at 2:1, 1000 ms at 4:1 and 2000 ms at 10:1. Measured against real Live, that averaged about 1.1 dB of difference, and up to about 2.4 dB on busy drums with a fast attack.

Do FL Studio compressors become Glue Compressor when going to Ableton?

No. DAWPORT converts FL compressors to Live's Compressor, Limiter or Multiband Dynamics. It never outputs a Glue Compressor.

Convert now