Short answer
FL Studio users often sidechain with Fruity Peak Controller. It sits on the kick's Mixer insert, follows the kick's level, and is linked to the bass insert's volume fader so the bass dips on every kick.
2 free conversions every month. No card required.
Live's audio effects don't move another track's fader like that. The usual native way is a Compressor on the bass with its sidechain listening to the kick. DAWPORT converts Peak Controller volume ducking into that setup, labelled as an approximation.
How Peak Controller ducking works
To rebuild it, DAWPORT measured Peak Controller with FL Studio renders at 48 kHz:
- It reads the louder of the left and right channels.
- It reacts instantly when the sound gets loud, holds for about 4 ms, then falls back at a steady speed set by Decay.
- Volume, Tension and Base shape how strongly that level becomes a control value.
- The link (usually "inverted", so loud means down) writes that value to the target. The optional link smoothing softens it.
- A Mixer fader can only move so fast. That also shapes the duck.
The Live equivalent, control by control
| Peak Controller + link | Ableton Live (converted) |
|---|---|
| The insert it sits on (the kick) | The Compressor's sidechain source, at Pre FX or Post FX |
| Linked target: another insert's fader | One or two Compressors on that track |
| Linked target: a Fruity Balance volume | One or two Compressors placed right after that Balance (which becomes Live's Utility) |
| Volume, Base, Tension | Compressor threshold, ratio and knee, fitted to FL's ducking curve |
| Decay, link smoothing | Compressor attack and release |
| The ducked track's resting volume | Kept as it was |
DAWPORT doesn't try to copy the knobs one to one. It does three things:
- It calculates the ducking curve: how many dB the target drops at each kick level.
- It calculates how fast the duck recovers.
- It fits Live's own Compressor to that curve and timing, using measurements of Live's Compressor.
When one Compressor can't follow a deep duck closely, DAWPORT uses two in a row.
The sidechain point follows where the Peak Controller sits:
- Pre FX when nothing audible comes before it on its insert.
- Post FX when nothing comes after it.
If it sits between other effects, it is not converted.
What DAWPORT does with it
When converting an FL Studio project to Ableton (DAWPORT 1.0.72 and later), each Peak Controller link is checked on its own. A link is converted when all of these hold:
- It uses the Peak output, not the LFO.
- It turns down another insert's volume fader or a Fruity Balance volume.
- Only this controller drives that target, and the target has no automation.
- The target is on another track, not the controller's own.
- The saved volume matches the target's resting level.
- DAWPORT's fit is clearly closer than leaving the ducking out.
The whole controller stays unconverted when:
- it is switched off or automated
- it is not on a Mixer slot
- its LFO is in use
- its settings fall outside the measured ranges
The conversion notes say which track gets turned down, which track it listens to, and how close the result is. The original controller settings are kept in the recovery data. When some links of a controller convert and others don't, the notes list the others with a plain reason.
A few specific Peak Controller setups that DAWPORT measured one by one use Live 12's Envelope Follower instead of a Compressor.
What sounds the same, and what differs
Close: the depth of the duck. The notes say how close the ducked level stayed to FL's measured behaviour on test material, as a figure for your project.
Can differ:
- Recovery speed. A compressor release is not the same shape as Peak Controller's straight-line fall.
- Wide stereo sources. Live's sidechain listens to the average of both sides, while FL uses the louder side, so Live ducks a little less.
- Full mutes. Where FL turns the sound fully off on loud moments, a compressor turns it down a lot instead, and the notes tell you by how many dB.
Tips for matching by hand in Live
- Put a Compressor on the track that should duck. Open its sidechain and pick the kick track.
- Start with a low threshold, a high ratio and a fast attack. Then set the release by ear until the bass comes back at the same speed as in FL.
- For a very deep, gated-sounding duck, add a second Compressor after the first.
- Leave the ducked track's fader where it was. The compressor only handles the dips.
Related
- Fruity Limiter in Ableton: the other common FL sidechain method
- Fruity Balance in Ableton
- All device equivalents

