Short answer

The Ableton Live equivalent of Fruity Multiband Compressor is Multiband Dynamics. Both devices:

Convert now

2 free conversions every month. No card required.

DAWPORT converts FL's multiband compressor to Multiband Dynamics. The reverse conversion also works for a narrower set of settings. Both directions are labelled as approximations.

How the controls correspond

Fruity Multiband Compressor Multiband Dynamics How DAWPORT carries it
Low / high crossover frequency Low-Mid and Mid-High split Measured FL crossover law, assuming 48 kHz
Band threshold Band threshold (above) Carried in dB, about 0.5 dB lower
Band ratio Band ratio (above) Measured law. FL compresses harder than its nominal ratio, so Live gets a steeper ratio, up to about 5:1
Band attack Band attack Shortened through a measured factor
Band release Band release Lengthened through a measured factor, because FL releases more slowly
Band gain Band output gain Carried in dB, with a small lift on low and high
Global gain Output gain Carried in dB
Band bypass Band switched off Passes unprocessed

Why aren't the numbers copied one to one? The two devices respond differently at the same setting. DAWPORT rendered Fruity Multiband Compressor states in FL Studio and Multiband Dynamics in Live 12, then fitted a law between them. In DAWPORT's modelled checks on held-out settings, copying the values directly was further off (about 0.55 to 1.84 dB) than the fitted law (about 0.46 to 1.30 dB).

What DAWPORT does: FL Studio to Ableton

Since DAWPORT 1.0.72, a Fruity Multiband Compressor on a Mixer insert converts to Multiband Dynamics when all of these are true:

When a project falls outside these limits, no Live device is added for that instance. The original settings are kept in the recovery data, and the conversion notes list it as not converted. When every band is bypassed, the bands pass through unprocessed, so no Live device is added for it either.

The conversion notes call it an approximation and say: "Multiband compression is present; band edges and transient response can differ slightly." In DAWPORT's test projects, the number of converted instances went from 0 to 10 with this release.

What DAWPORT does: Ableton to FL Studio

Multiband Dynamics converts to Fruity Multiband Compressor only in a tight, measured setup:

Threshold, ratio, attack, release and gain are carried in their real units. The crossover points use the measured FL law. Anything outside this setup is reported and left out; the rest of the project still converts.

Multiband Dynamics is also used for a different FL device: DAWPORT rebuilds Soundgoodizer with it, because Soundgoodizer behaves like a fixed three-band maximizer.

What sounds the same, and what differs

Close: where the bands split, how much each band is pushed down, and the overall tone and level.

Can differ:

On real project settings, the level on drums and mixes differed by about 0.4 to 1.3 dB on average. Live can be up to about 1 dB quieter.

Tips for matching by hand

  1. Set the two split points first. Solo each band in both DAWs and compare by ear.
  2. Expect FL to squeeze a little harder at the same ratio. Start Live one notch higher.
  3. FL's band release feels slower. Lengthen Live's release until the pumping matches.
  4. Match the output at the same loudness before you judge the tone.
  5. Use FL's linear-phase mode only if you need it. Live's Multiband Dynamics has no linear-phase mode, and DAWPORT doesn't convert that mode.

Related

Questions

What is the Ableton equivalent of Fruity Multiband Compressor?

Multiband Dynamics. Both split the sound into low, mid and high bands with two crossover points and compress each band on its own.

Does DAWPORT convert Fruity Multiband Compressor to Ableton?

Yes, since version 1.0.72, as a labelled approximation to Multiband Dynamics. Linear-phase mode, the output limiter, muted bands, a slot mix turned down from full and automation are not converted. Those settings stay in the recovery data.

Does it work the other way, from Ableton to FL Studio?

Yes, for a narrow set of Multiband Dynamics settings: all three bands active, soft knee, RMS detection, downward compression only, Amount and Time at 100 percent, and no sidechain or automation.

How close is the converted multiband compression?

On real project settings, FL Studio and Live renders differed by about 0.4 to 1.3 dB on average on drums and mixes. Live can come out up to about 1 dB quieter.

Convert now