Short answer
Ableton Live's Auto Pan moves a sound's level in the left and right channels with an LFO, from gentle stereo motion to tremolo and rhythmic chopping. FL Studio has no single device that does this. FL users usually draw an automation clip, link an LFO, or use a panning plug-in.
2 free conversions every month. No card required.
When DAWPORT converts a Live Set to FL Studio, it rebuilds Auto Pan as two Fruity Stereo Shapers in the track's Mixer insert. Each one handles one channel, and its Mixer slot mix knob follows an automation curve drawn from your Auto Pan settings. The conversion note reads: "Approximate: Auto Pan was rebuilt as two Fruity Stereo Shapers whose mixer slot mix knobs follow automation curves (one per channel), so the left/right volume movement can be edited in FL Studio."
What Auto Pan really does
The name suggests panning, but in DAWPORT's measurements of real Live 12 renders, Auto Pan doesn't move sound from one side to the other. It turns each channel down and back up on its own, with the right channel offset in time from the left by the Phase control. At an Amount of zero, nothing moves.
That is why DAWPORT writes two volume curves, one per channel, instead of automating FL's pan knob. Each Fruity Stereo Shaper silences one channel on its wet path, so turning its slot mix knob up turns that channel down.
How the controls correspond
| Auto Pan | FL Studio (converted) | Notes |
|---|---|---|
| Amount | Depth of both curves | Carried |
| Rate, synced | Curve length in beats | From Live's division list, read in 4/4 |
| Rate, in Hz | Curve length in beats at the Set's tempo | Needs a fixed tempo |
| Phase | Offset between the left and right curves | Carried |
| Offset | Start position of both curves | Carried |
| Shape | Bend of the curves | Measured on sine; an approximation on other waveforms |
| Waveform: sine, triangle, saw down | Same curve shape | Carried |
| Waveform: random | Four stepped values per cycle, with Live's Width | The random values differ from Live's |
| Invert | Inverted curves | Carried |
| Spin (free-running Hz mode) | Right curve runs faster by the Spin amount | Approximation, not yet verified on Live renders |
| Device on or off | Both Stereo Shapers on or bypassed | Carried |
The curves start at the beginning of the arrangement and run to the end of the last clip. After that, the final value holds. DAWPORT picks the curve resolution so each cycle has at least 24 points, more for strong Shape settings, up to 256 steps per beat.
What DAWPORT does with Auto Pan
Converted (approximation). A classic Auto Pan from a Live 11 or Live 12 Set converts when nothing else controls it. The notes add a line for each approximation, for example when a synced rate hasn't been checked against Live renders, or when a free-running Hz rate is turned into beats at the Set's tempo.
Not converted, listed in the notes and kept in the recovery data:
- Auto Pan-Tremolo, the newer Live 12 device
- an Auto Pan with any automation, modulation, rack macro or MIDI mapping on its controls
- a rate in Hz when the Set's tempo changes
- a rate too fast to draw as an editable automation curve
- a Mixer insert without two free effect slots next to each other
- an Auto Pan inside an Audio Effect Rack that DAWPORT rebuilds as a Patcher. The Patcher can't hold generated slot curves, so that whole rack is left out. See Audio Effect Rack in FL Studio.
The rest of the project still converts.
How close it sounds
These figures come from comparing DAWPORT's curves with real Live 12 renders:
- Sine, triangle and saw down, with phase, offset, invert and synced rates: within about 0.005 to 0.013 RMS gain, around 1 percent of full level.
- Shape: fitted at 25, 50 and 100 percent, with RMS errors of 0.001 to 0.005.
- A real percussion loop not used for fitting: 0.041 RMS gain error, against 0.040 for the best curve possible and 0.092 without the Shape fit.
The curves were checked in FL Studio 26 at 48 kHz, and DAWPORT builds them for a 48 kHz project. Random waveforms and free-running Spin are labelled approximations.
Tips for working with it in FL Studio
- Find the two clips in the Playlist. They are named after the track, ending in "stereo modulation L" and "stereo modulation R".
- To change the depth, scale both clips' values together. To change the speed, edit the clip pattern, or redraw it with FL's automation clip LFO tool.
- For a classic FL-style auto pan instead, delete the two clips and Stereo Shapers and automate the Mixer track's pan knob.
- Keep two effect slots free on tracks that use Auto Pan in Live, so DAWPORT has room for the two Stereo Shapers.
Related
- Ableton Utility in FL Studio: gain and width, also built on Fruity Stereo Shaper
- Ableton Audio Effect Rack in FL Studio
- FL Studio ↔ Ableton device equivalents table
- Convert Ableton to FL Studio

