Short answer
- Ableton Saturator → FL Studio: the closest native tool is Fruity WaveShaper. DAWPORT converts Saturator by drawing Live's measured saturation curve into WaveShaper.
- Fruity Soft Clipper → Ableton: the closest native tool is Saturator. DAWPORT converts Fruity Soft Clipper to Saturator's Bass Shaper mode, but only at its default setting.
Both are labelled in the conversion notes. The Saturator conversion is an approximation, and the Soft Clipper one is a restricted mapping.
2 free conversions every month. No card required.
Why WaveShaper is the right match for Saturator
A saturator is, at its core, a transfer curve: for every input level, a fixed output level. Live's Saturator offers a set of preset curves (Analog Clip, Soft Sine, Medium Curve and so on) plus Drive, Output and Dry/Wet. Fruity WaveShaper lets you draw any curve.
So, rather than guessing which FL distortion "sounds like" Saturator, DAWPORT draws Saturator's measured curve, at your Drive setting, straight into WaveShaper.
How the controls correspond (Ableton → FL Studio)
| Saturator | Fruity WaveShaper / FL | Notes |
|---|---|---|
| Curve type | The drawn curve | Fitted from real Live recordings |
| Drive | Built into the curve | Each Drive setting gets its own curve |
| Output | WaveShaper POST level | |
| Dry/Wet | Mixer slot mix knob | |
| Output soft clip | Part of the drawn curve | Measured |
| Output hard clip | Part of the drawn curve | Drawn at 0 dBFS, not yet verified against Live |
| Hi-Quality | — | Not reproduced; more aliasing on bright, hard-driven sounds |
| DC filter | — | Not carried |
| Color (with Base or Depth) | — | Not converted |
| Waveshaper mode | — | Not converted |
Converted curve types: Analog Clip, Soft Sine, Medium Curve, Hard Curve, Sinoid Fold, Digital Clip and Bass Shaper.
WaveShaper's PRE knob is set to its minimum, so the curve covers input up to about +9.5 dBFS. Anything louder is held at the curve's end value.
A plain Digital Clip, fully wet with Color and the DC filter off, takes a dedicated path instead: a Patcher hard-clip setup.
What DAWPORT does with Saturator
Since DAWPORT 1.0.70, converting a Live Set to FL Studio turns each supported Saturator into Fruity WaveShaper. The conversion notes say it is an approximation and explain the curve. On drums the level matched Live within 0.01 dB.
The notes also flag the known gaps when they apply:
- Hi-Quality on: levels match within about 0.2 dB on drums, but bright material driven hard gets more aliasing (up to about 1 dB extra high-frequency energy on a 10 kHz tone).
- Sinoid Fold with Hi-Quality on bright, loud material differs strongly.
- Hard Curve beyond the measured input range is extrapolated.
- Bass Shaper was tested in Live at one threshold only.
Automated Saturators, Waveshaper mode and Color with Base or Depth set are not converted. They are reported, and the rest of the project still converts.
Fruity Soft Clipper in Ableton
Fruity Soft Clipper has two controls: Threshold and Post gain. It rounds off peaks above the threshold.
In Live, the closest native device is Saturator. DAWPORT's measurements found that its Bass Shaper curve can closely match Soft Clipper's default curve.
DAWPORT converts Fruity Soft Clipper to Saturator only in its default setup:
- the default threshold, with Post gain at unity
- no automation and no sidechain, with the Mixer slot mix fully up
- DAWPORT can confirm from the project that the signal going into it stays below about +6 dBFS
- 48 kHz processing
Moved thresholds, other post gains, automation and louder input are not converted. They are listed in the conversion notes, and the settings stay in the converted project's recovery data.
This mapping is narrow. If your project uses Soft Clipper at a custom threshold, expect to recreate it by hand (tips below).
Fruity WaveShaper → Ableton is also narrow: only simple curves (2 to 7 points spread out across the range) convert. They become an Audio Effect Rack of Saturator (Digital Clip) and Utility chains.
Tips for matching by hand
Saturator in FL:
- Use Fruity WaveShaper. Draw a gentle S-curve for Analog Clip or Soft Sine, and a sharper knee for Hard Curve.
- Raise the input before WaveShaper for "drive", and use POST to bring the level back.
- Use the Mixer slot mix knob for Saturator's Dry/Wet.
Soft Clipper in Live:
- Use Saturator in Bass Shaper or Soft Sine mode.
- Lower Drive until only the peaks are touched.
- Keep Output at 0 dB, then compare peak levels on the master meter.

