Short answer
Ableton's Auto Filter is a filter with resonance, drive, an LFO and an envelope follower, all in one device. FL Studio splits those jobs across several plug-ins.
2 free conversions every month. No card required.
For the filter itself (low-pass, high-pass, band-pass or notch, swept by automation), the closest native FL tool that DAWPORT can match closely is a filter band in Fruity Parametric EQ 2. When converting a Live Set to FL Studio, DAWPORT turns Auto Filter into Parametric EQ 2 and labels it as an approximation.
How the controls correspond
| Auto Filter | Fruity Parametric EQ 2 (converted) | Notes |
|---|---|---|
| Low-pass 12 / 24 dB | Low-pass band | 24 dB uses a second stage |
| High-pass 12 / 24 dB | High-pass band | |
| Band-pass | Band-pass band | Level matched with the EQ's output gain |
| Notch | Notch band | |
| Frequency (cutoff) | Band frequency | Same Hz |
| Resonance | Band width (Q) | Measured Live resonance curve, converted to Q |
| Cutoff automation | Band frequency automation | In Hz; curved segments are sampled into points |
| Device on/off automation | Mixer slot on/off | Since 1.0.72 |
| LFO, envelope follower | — | Movement not carried |
| Drive, circuit types other than Clean | — | Not converted |
| Dry/Wet | — | Must be fully wet |
Live's Resonance knob doesn't map to a fixed Q, so DAWPORT measured Live's resonance-to-peak behaviour. It then picks the Parametric EQ 2 width that gives the same peak. For band-pass, it also restores the level, because a narrow band-pass in Live has a different overall level than the same band in Parametric EQ 2.
What DAWPORT does with Auto Filter
DAWPORT 1.0.70 added this mapping for both the older Auto Filter and the Live 12 Auto Filter. An Auto Filter converts to Fruity Parametric EQ 2 when:
- the filter uses the clean circuit (SVF in the newer Auto Filter; the other circuits add their own character)
- drive is at 0 and the output is at unity
- resonance is moderate: up to 70% at 12 dB, up to 50% at 24 dB
- Dry/Wet is fully wet, and no sidechain is used
- Hi-Quality, the output soft clip and the older Auto Filter's legacy mode are off
- only cutoff and on/off are automated
If an LFO or envelope follower is active, the filter still converts at its set cutoff (and its cutoff automation, if any). The LFO or envelope follower movement is left out, and the notes say so.
The conversion notes describe it as approximate and not identical to Live's filter. In DAWPORT's tests against real Live, the sound matched within about 0.1 dB on average. Settings outside this range (other circuits, drive, heavy resonance, or automation of other controls) mean the Auto Filter is reported and left out, and the rest of the project still converts.
The calibration was measured at 48 kHz. When the Live Set doesn't record its sample rate, DAWPORT assumes 48 kHz and says so in the notes.
The other direction: FL filters in Ableton
From FL Studio to Ableton, filter coverage is narrower:
- Fruity Filter converts only in a static, measured setup: cutoff within the measured range, no resonance, no x2 oversampling or Center, no automation, slot mix fully up. It becomes an Audio Effect Rack built from Live Auto Filter and Utility devices, labelled as an approximation.
- Fruity Love Philter is not converted. The only exception is a Love Philter whose Mixer slot mix is at zero, which has no audible effect anyway.
- Low-cut, high-cut and notch bands in Fruity Parametric EQ 2 convert to EQ Eight; band-pass bands do not. See Fruity Parametric EQ 2 in Ableton.
What sounds the same, and what differs
Close:
- the filter type and cutoff, including automated sweeps
- moderate resonance peaks
Differs:
- Auto Filter's analogue-style circuits and drive. These are not converted at all.
- High resonance, which is not converted.
- LFO wobble. You need to rebuild it in FL.
Tips for rebuilding Auto Filter by hand in FL Studio
- For a plain sweep, automate a Parametric EQ 2 high-pass or low-pass band's frequency. This is what DAWPORT does.
- For LFO wobble, Fruity Love Philter or an automation clip with an LFO shape on a filter cutoff gets you closest.
- For drive or "dirty" circuits, add saturation before or after the filter. See Saturator in FL Studio.
- If the converted resonance peak sounds a little different, narrow or widen the band slightly by ear.

