Short answer
Fruity Parametric EQ 2 in FL Studio and EQ Eight in Ableton Live are each other's closest equivalent. Both are parametric EQs with:
2 free conversions every month. No card required.
- bell (peaking) bands
- low and high shelves
- notch
- low-cut and high-cut filters
DAWPORT converts in both directions. EQ is one of the closer matches between the two DAWs, but the details still differ, especially filter slopes, band width and high-quality modes.
How the controls correspond
| Fruity Parametric EQ 2 | EQ Eight | Notes |
|---|---|---|
| 7 bands | 8 bands | Live → FL: 8 active bands need two Parametric EQ 2s in a row |
| Band frequency | Frequency | Same Hz |
| Band gain (±18 dB) | Gain (±15 dB) | Larger FL boosts and cuts are split over two EQ Eight bands |
| Band width | Q | Measured width ↔ Q laws, not a straight copy |
| Peaking | Bell | |
| Low shelf / high shelf | Low shelf / high shelf | |
| Notch | Notch | |
| Low pass / high pass with slope | Low cut / high cut (12 or 48 dB/oct) | FL slopes are built from 12 dB/oct EQ Eight stages |
| Band pass | — | No EQ Eight equivalent |
| Main level | Output gain | Beyond ±12 dB, a Utility takes the rest |
| HQ / linear-phase modes | — | Matched by response only |
Why does band width need translating? FL's width control and Live's Q are different scales. A "50%" width in FL is not any particular Q. DAWPORT converts each band to its real shape first, using measured FL laws and a model of EQ Eight, then picks the EQ Eight settings that come closest to that curve.
FL Studio to Ableton: what DAWPORT does
- Standard settings map band by band onto EQ Eight.
- Steep cuts (FL's steeper slopes) are rebuilt from several 12 dB/oct sections. When one EQ Eight doesn't have enough bands, DAWPORT adds more in a row, up to four.
- Large boosts or cuts beyond EQ Eight's ±15 dB are split across two stacked bands whose combined curve matches.
- A Mixer slot mix knob turned down from full becomes an Audio Effect Rack with a Wet chain (the EQ) and a Dry chain.
- HQ, enhanced and "Plus" quality modes are fitted on their measured response. Linear phase is matched on frequency response only. Live's EQ Eight doesn't reproduce linear phase.
When DAWPORT has to approximate an EQ (for example HQ modes, steep cuts or very large boosts), the notes say "Converted to EQ Eight as an approximation." and give the expected difference from the original curve.
EQ automation
Band frequency and gain automation carries over to EQ Eight. Since 1.0.72, this also works when DAWPORT has to approximate the EQ. It re-fits each automated band at every automation point and writes EQ Eight frequency, gain and Q curves. Q moves along with gain so the band keeps its shape. Main level automation and on/off automation carry too.
On an approximated EQ, these are not carried yet:
- automation of band width or band type
- automation of the Mixer slot's mix knob
- automation that changes how many EQ Eight bands a band needs
- automation that would move a band outside EQ Eight's range, or too far from the FL curve
In these cases that EQ is left out, and the notes say why.
What is left out
- Band-pass bands. EQ Eight has no band-pass type, so that EQ is not converted.
- Linear-phase cuts steeper than 12 dB/oct. Real FL Studio and Live renders of these differed by about 2 to 6 dB on average. DAWPORT leaves them out with a plain notice rather than guessing.
In both cases the original settings stay in the converted project's recovery data.
Ableton to FL Studio: what DAWPORT does
EQ Eight becomes Fruity Parametric EQ 2:
- Bell, shelves, notch, low cut 12 and high cut 12 map to the same FL band types.
- Low cut 48 and high cut 48 become FL's steep slope settings. These are approximated.
- If all 8 bands are active, bands 1 to 7 go into one Parametric EQ 2 and band 8 into a second one right after it.
- Band gain and frequency automation carry over. Turning EQ Eight on and off becomes the FL Mixer slot's on/off switch. Other EQ Eight automation (Q, band type, global gain) is reported rather than carried.
- L/R or M/S mode with different settings per side is not converted.
Tips for matching by hand
- Copy frequency and gain directly. Then adjust Q or width by ear, or with an analyser, instead of copying the number.
- For FL's steep cuts, use EQ Eight's 48 dB/oct mode, or stack two 12 dB/oct bands at the same frequency.
- Need a band-pass in Live? Use a low cut plus a high cut. Auto Filter also has a band-pass mode.
- Keep big boosts within ±15 dB per band in Live, or spread them over two bands.
Related
- Auto Filter in FL Studio: Live's filter converts to Parametric EQ 2 too
- All device equivalents
- Convert FL Studio to Ableton · Convert Ableton to FL Studio

