Short answer
FL Studio's stock reverb is Fruity Reeverb 2. People often search for it as "Fruity Reverb 2". Ableton Live has two stock reverbs:
2 free conversions every month. No card required.
- Reverb, the classic one
- Hybrid Reverb, which has an algorithmic section and a convolution section
The closest match for Reeverb 2 is Hybrid Reverb's algorithmic section, using the Dark Hall algorithm. That is what DAWPORT uses when converting FL Studio projects to Ableton. In the other direction, both Live reverbs convert to Fruity Reeverb 2.
Every reverb conversion is labelled as an approximation. Two different reverb engines never sound identical, but DAWPORT aims to keep the length, size and dry/wet balance close.
How the controls correspond (FL Studio → Ableton)
| Fruity Reeverb 2 | Ableton (converted) | Notes |
|---|---|---|
| Pre-delay | Hybrid Reverb pre-delay | Converted to ms. Tempo-synced pre-delay is resolved at the project tempo (within a measured range) |
| Decay | Decay | In seconds |
| Size | Size | |
| Diffusion | Shape | Approximate: follows the control's intent |
| Bass multiplier / crossover | Bass multiplier / crossover | |
| Damping | Damping | Approximate: follows the control's intent, not an equivalent filter |
| Low cut / High cut | Hybrid Reverb EQ low and high cut, before the reverb | In Hz |
| Stereo separation | Stereo width | |
| Modulation depth | Modulation | |
| Modulation speed | — | Not carried |
| Dry level | Dry chain Utility | FL's measured volume curve |
| Wet level + early reflections | Wet chain Utility | Combined into one wet level |
| Mixer slot mix knob | Folded into both levels |
DAWPORT wraps the reverb in an Audio Effect Rack with a Dry chain and a Wet chain, each with a Utility for its level. Inside the Wet chain, a Utility first feeds the reverb the mid (mono) part of the input, which is how DAWPORT models Reeverb 2's input. The reverb runs fully wet. This keeps FL's separate dry and wet knobs working as they did, rather than squeezing them into one Dry/Wet knob.
What DAWPORT does: FL Studio → Ableton
- Converted (approximation): a normal Reeverb 2 becomes the Dry/Wet rack described above, with Live's own device names.
- Dry only (wet and early reflections both at zero): the reverb is silent, so you get just a Utility.
- Level automation (since 1.0.70): automation of Dry, Wet, the slot mix and on/off becomes Utility gain automation, following FL's measured volume curves. The notes label it as an approximation and say the original settings and automation are kept in the conversion's recovery data.
- Not converted: side (mid/side) processing turned on, automation of any other reverb control (including early reflections), or tempo-synced pre-delay outside the measured range. The notes explain why.
Early reflections are not rebuilt as separate early echoes. Their level is folded into the wet level.
What DAWPORT does: Ableton → FL Studio
Both Live reverbs become Fruity Reeverb 2, as approximations:
- Reverb: pre-delay, decay, room size and diffusion carry over. The input filter becomes Reeverb 2's low and high cut. The low shelf sets the bass multiplier, the high shelf sets the damping, Chorus sets the modulation, and stereo sets the width. Dry/Wet, reflection level and diffuse level are matched through measured level curves. DAWPORT 1.0.72 refined this level estimate so it follows room size and decay.
- Hybrid Reverb: converts when its routing is set to the algorithm only and it uses the Dark Hall algorithm. Freeze, Vintage, Bass Mono and synced pre-delay must be off, and its EQ is carried only as low and high cuts. A Hybrid Reverb that uses the convolution section, another algorithm (Quartz, Shimmer, Tides, Prism) or one of those other settings is not converted.
These are reported and not converted:
- automated, sidechained or frozen reverbs
- reverbs driven by unresolved rack macros
These are not reproduced: the exact reflection pattern, Spin, the quality setting and the high filter type.
What sounds the same, and what differs
Close:
- reverb length (decay)
- the sense of size
- dark or bright tone from cuts and damping
- the dry/wet balance
Can differ:
- the early reflection pattern
- the modulation movement
- the texture of the tail, since Reeverb 2 and Live's reverbs use different engines
Tips for matching by hand
- Match decay time first, then use the low and high cuts to match the tone.
- In Live, put the reverb on a return track or in a Dry/Wet rack if you want FL-style separate dry and wet levels.
- If the Live version sounds wider, lower the stereo width a little.
- Compare tails on a short, dry sound like a snare or a clap. Differences are easiest to hear there.
Related
- Fruity Delay 3 in Ableton
- Fruity Convolver in Ableton: impulse-response reverb and Hybrid Reverb's convolution section
- All device equivalents
- Convert FL Studio to Ableton

