Short answer
The Ableton Live equivalent of Fruity Delay 3 is Delay. Both give you:
2 free conversions every month. No card required.
- delay time, synced to the beat or in milliseconds
- feedback
- ping-pong
- a filter on the repeats
Fruity Delay 3 also has modulation, diffusion, distortion and lo-fi sections. Delay doesn't have those. Live's Echo covers some of that character instead.
DAWPORT converts delays in both directions:
- FL → Live: Fruity Delay 3 and Fruity Delay 2 become Live's Delay.
- Live → FL: Delay and Echo become Fruity Delay 3.
All delay conversions are labelled as approximations.
How the controls correspond (FL Studio → Ableton)
| Fruity Delay 3 | Live Delay (converted) | Notes |
|---|---|---|
| Time, tempo-synced | Delay sync | Live offers 1, 2, 3, 4, 5, 6, 8 and 16 sixteenths. Other values become milliseconds |
| Time, free | Delay time (ms) | Measured FL time curve, 1 ms to 5 s |
| Feedback | Feedback | Measured per-repeat level, up to Live's 95% |
| Ping-pong | Ping Pong | Approximated; FL's stereo offset sets the ping-pong balance |
| Feedback low/high cut | Delay's filter | Measured corners mapped onto Delay's band filter |
| Input wet, output dry and wet | Dry and Wet chain volumes | FL's measured level laws |
| Mixer slot mix knob | Folded into the chain volumes | |
| Modulation, diffusion, distortion, bit/sample-rate reduction, tone, stereo spread | — | Not carried, and listed in the notes |
DAWPORT doesn't use Delay's own Dry/Wet knob. It puts Delay fully wet inside an Audio Effect Rack with a Dry chain and a Wet chain. FL's Delay 3 has separate dry and wet output levels, and this keeps both close to where they were in FL. A single Dry/Wet knob can't hold both.
What DAWPORT does: FL Studio → Ableton
Since DAWPORT 1.0.70:
- Fruity Delay 3 in Stereo or Ping-pong mode converts as described above. These are left out and named in the conversion notes:
- the band-pass repeat filter and filter resonance
- the stereo offset in stereo mode
- time and filter modulation
- diffusion, distortion, bit and sample-rate reduction, output tone and stereo spread
- Fruity Delay 2 converts the same way. Its stereo offset becomes separate left and right delay times. Normal, inverted and ping-pong modes are handled. Its feedback filter is not carried.
- Automation: Delay 3's slot mix, input wet and on/off automation carry over. If other Delay 3 controls are automated, that Delay 3 is not converted. An automated (remote-controlled) Delay 2 is not converted either.
- Wet output at zero: a Delay 3 whose wet output is turned all the way down makes no echoes, so it becomes a plain Utility at the dry level.
- Not converted: Delay 3 in Mono mode. The notes say why.
The conversion notes label every converted delay as an approximation, list what was left out, and say that the original settings are kept in the conversion's recovery data.
What DAWPORT does: Ableton → FL Studio
Live's Delay and Echo become Fruity Delay 3:
- Time: synced or free. Synced values from 1 to 16 sixteenths carry, including dotted and triplet settings. Free times from 1 to 1000 ms carry.
- Feedback: carried, through the measured Delay 3 scale.
- Dry/Wet: carried to Delay 3's output levels.
- Ping-pong: Delay's Ping Pong and Echo's ping-pong mode become Delay 3's ping-pong. The two devices bounce differently, so the notes give the level difference for the left and right repeats.
- Fruity Balance: added after Delay 3 only when needed. This happens when Live's ping-pong wet level is higher than Delay 3 can reach, when Echo's output gain isn't at unity, or when a clean Echo's input gain is turned down.
These convert, but only partly. The time and feedback carry, while these parts are not carried:
- the filter and modulation
- Echo's reverb, noise, wobble and ducking
- automation of the delay's controls
These are not converted at all:
- different left and right delay times, or active offsets
- Echo in mid/side mode
- Delay with Freeze on
- Feedback of 100 percent or more with the filter on. Without the filter in the loop, the repeats would never die away.
- delay controls driven by rack macros that can't be resolved
What sounds the same, and what differs
Close:
- the delay time and groove
- how many repeats you hear, and how fast they fade
- the dry/wet balance
Can differ:
- ping-pong placement
- the tone of the repeats when a filter or modulation was used
- Echo's analogue-style character, which Fruity Delay 3 doesn't copy
Tips for matching by hand
- Set the same synced time, then match feedback by counting audible repeats.
- Live's Delay sync doesn't offer every note value. For odd values, use free time in ms (60000 ÷ BPM ÷ 4 = one sixteenth).
- Want FL-style separate dry and wet levels in Live? Put Delay on a return track, or in a rack with a dry chain.
- Recreate modulation or lo-fi on the repeats with Echo, or with Chorus-Ensemble or Redux after the Delay in the wet chain.

