Short answer

The closest Ableton Live match for Fruity Chorus is Chorus-Ensemble. Both make a sound wider and thicker by adding copies of it that are delayed by a few milliseconds, with an LFO moving that delay up and down.

Convert now

2 free conversions every month. No card required.

When DAWPORT converts an FL Studio project, a Fruity Chorus on a Mixer insert becomes a Chorus-Ensemble inside an Audio Effect Rack. It is labelled as an approximation in the conversion notes. The two devices build their chorus voices differently, so the result is close in rate, level and brightness, but the depth and character can sound a little different.

How the two devices differ

Fruity Chorus gives you more separate controls than Chorus-Ensemble:

Chorus-Ensemble has one Rate and one Amount, with a Classic mode (two delay lines), an Ensemble mode (three delay lines) and a Vibrato mode. DAWPORT uses Classic or Ensemble. It has its own high-pass filter, feedback, width and warmth controls. So some Fruity Chorus settings have a direct counterpart and some don't.

How the controls correspond

Fruity Chorus Chorus-Ensemble (converted) How DAWPORT carries it
Delay Mode Short delays use Classic. Longer delays (from about 6.8 ms) use Ensemble
Depth Amount Converted from FL's depth in milliseconds. The notes call the depth an approximation
LFO 1, 2 and 3 rates Rate The three rates are combined into one average rate (0.1 to 15 Hz)
Cross type set to high-pass High-pass filter on Carried
Cross cutoff High-pass frequency Measured FL curve, 20 to 2000 Hz
Cross type set to low-pass — Left out, and named in the notes
LFO shapes — Left out (Live's own LFO is used)
Stereo (LFO phase between sides) — Left out
Wet only, Mixer slot mix Dry and Wet chain volumes Levels measured from real FL Studio renders

DAWPORT sets Chorus-Ensemble fully wet, with feedback, warmth and vibrato off, width at 100 percent and output at unity. The dry signal comes from the rack's Dry chain instead. In DAWPORT's FL Studio renders, Fruity Chorus passes its dry signal at about 0.70 of the input and its summed voices at about 0.99. The rack chains are set from those measured levels, combined with the Mixer slot's mix knob.

What DAWPORT does with Fruity Chorus

Converted (approximation). A Fruity Chorus on a Mixer insert, with no automation and no sidechain into it, becomes the rack described above. Live's own device names are used: you will see Audio Effect Rack and Chorus-Ensemble, not "Fruity Chorus".

The conversion note says the effect was converted "as an approximation". It says the LFO rate and wet high-pass carry over, that Live's own chorus voices replace the source voices, and that the chorus depth may sound slightly different. It then lists what was approximated (for example, that three LFO rates were averaged into one), what was not carried, and that the original settings are kept in the conversion's recovery data.

Not converted. A Fruity Chorus is left out, listed in the notes and kept in the recovery data when:

The rest of the project still converts.

What sounds the same, and what differs

Close:

Can differ:

In DAWPORT's checks of real project settings against FL Studio renders, the average difference across third-octave frequency bands was about 0.55 to 0.7 dB. That is a useful match, not an exact one, so compare by ear.

Ableton Chorus-Ensemble in FL Studio (the other direction)

DAWPORT doesn't convert Chorus-Ensemble from Live to FL Studio yet. Its two- and three-voice modes, vibrato, feedback, width and warmth have no verified FL Studio match. Going from Ableton to FL Studio, it is listed as not converted, and the rest of the project still converts. You can rebuild it by hand with Fruity Chorus on the same Mixer insert.

Tips for matching by hand

  1. Start with Chorus-Ensemble's Rate at roughly the average of your three Fruity Chorus LFO rates.
  2. Use Classic mode for short Fruity Chorus delays and Ensemble mode for longer, lusher ones.
  3. If you used the cross filter to chorus only the highs, turn on Chorus-Ensemble's high-pass at the same frequency.
  4. To keep FL's separate dry and wet knobs, put Chorus-Ensemble fully wet in a rack with a dry chain, or on a return track.
  5. Compare on a sustained pad or chord. Depth differences are easiest to hear there.

Related

Questions

What is the Ableton equivalent of Fruity Chorus?

Live's Chorus-Ensemble. Both thicken a sound by mixing in copies of it that are delayed by a few milliseconds, with the delay swept by an LFO. Fruity Chorus has three LFOs and a cross filter; Chorus-Ensemble has one rate control, Classic, Ensemble and Vibrato modes, and its own filter and width settings.

Does DAWPORT convert Fruity Chorus to Ableton?

Yes, since DAWPORT 1.0.70, as a labelled approximation. Fruity Chorus becomes a fully wet Chorus-Ensemble inside an Audio Effect Rack with a Dry chain and a Wet chain, so FL's dry and wet levels stay close to where they were.

Does Fruity Chorus automation carry over?

No. If any Fruity Chorus control, its on/off switch or its Mixer slot is automated or linked to a controller, that Fruity Chorus is not converted. Its settings stay in the conversion's recovery data and the notes list it.

Can Live's Chorus-Ensemble be converted to FL Studio?

Not yet. DAWPORT has no verified FL Studio match for Chorus-Ensemble, so going from Ableton to FL Studio it is reported as not converted and the rest of the project still converts.

Convert now