Short answer

Fruity Convolver is FL Studio's convolution reverb: it plays your sound through an impulse response (IR), a short recording that captures how a room, hall, plate or speaker sounds. In Ableton Live, the device that can do the same is Hybrid Reverb, using its convolution section. Live's classic Reverb is algorithmic and can't load an IR.

Convert now

2 free conversions every month. No card required.

When DAWPORT converts an FL Studio project, a Fruity Convolver with static settings becomes an Audio Effect Rack built around a Hybrid Reverb, with Utility devices for the levels and the stereo width. The impulse response has to be part of the upload.

How DAWPORT rebuilds it

Fruity Convolver does more than load an IR. Its editor can shape the IR with a volume envelope, an EQ curve, pre-delay and normalising. Hybrid Reverb has no editor like that. So DAWPORT does that shaping ahead of time:

  1. It reads the impulse response from your upload.
  2. It applies Fruity Convolver's normalising, volume envelope, pre-delay, self-convolution and (where used) EQ curve, using laws measured from real FL Studio renders.
  3. It saves the result as a new impulse response file in the converted project and loads it into Hybrid Reverb. Your original IR file is packaged with the project too.

Hybrid Reverb is then set to play only its convolution section, fully wet, with its own EQ, pre-delay, Vintage and Bass Mono off, so the prepared IR is what you hear.

How the controls correspond

Fruity Convolver Ableton Live (converted) How DAWPORT carries it
Impulse response Hybrid Reverb convolution IR A prepared copy of the IR
Normalize Built into the prepared IR Measured FL normalising level
Volume envelope Built into the prepared IR Simple envelopes only (see below)
Pre-delay Silence at the start of the prepared IR At measured pre-delay settings
Self-convolution Built into the prepared IR Carried
EQ envelope Built into the prepared IR Approximation, labelled in the notes
Wet level Utility gain in the Wet convolution chain Measured FL level curve
Dry level Utility gain in the Internal dry chain Measured FL level curve
Mixer slot mix knob Utility gain in the Host dry chain, and scales the other two Linear crossfade, as in FL
Input stereo separation Utility Width before Hybrid Reverb Measured FL law
Wet stereo separation Utility Width after Hybrid Reverb Measured FL law
Stretch — Must be at its default to convert

The dry chains also get a two-sample Align Delay. Hybrid Reverb's convolution output runs two samples behind a plain rack chain, and this keeps the dry and wet paths lined up.

What converts and what doesn't

Converted. A Fruity Convolver whose impulse response is available, with settings in the measured range, becomes the rack above. If its EQ envelope is in use, that EQ is applied to the prepared IR as an approximation, and the notes say it "may sound slightly different".

Left out, listed in the notes and kept in the recovery data, when:

The rest of the project still converts.

Get the impulse response into your upload

FL Studio projects store the path to your IR, not always the audio itself. If you upload only the .flp file, the IR stays on your computer and DAWPORT can't use it. To include it, copy the IR into your project folder and upload the folder as a .zip, .rar or .7z archive. If you use FL Studio's zipped project package, check that the IR file is inside it. Upload limits: .flp and .als files up to 16 MB, or .zip, .rar and .7z archives up to 512 MB. See samples and missing media for the details.

What sounds the same, and what differs

Close:

Can differ:

DAWPORT checked this setup on held-out test settings and by saving and reopening the converted Sets in Live 12.4.5. It is still a rebuild with a different device, so compare by ear.

Ableton Hybrid Reverb in FL Studio (the other direction)

DAWPORT doesn't convert Hybrid Reverb's convolution section to Fruity Convolver. Going from Ableton to FL Studio, a Hybrid Reverb that uses convolution is reported as not converted. A Hybrid Reverb that uses only its algorithm section, with the Dark Hall algorithm and a few other conditions, can become Fruity Reeverb 2. See Fruity Reeverb 2 in Ableton for that mapping.

Tips for matching by hand

  1. Drag the same IR file into Hybrid Reverb's convolution section and set the routing so only convolution is heard.
  2. Put Hybrid Reverb in an Audio Effect Rack with a dry chain if you want FL-style separate dry and wet levels.
  3. Rebuild Fruity Convolver's volume envelope with Hybrid Reverb's IR attack, decay and size controls, or render the shaped IR from FL Studio and load that.
  4. Use Utility's Width before or after the reverb to match FL's stereo separation.

Related

Questions

What is the Ableton equivalent of Fruity Convolver?

Hybrid Reverb, using its convolution section. Both play your sound through an impulse response (IR), a recording of a real or designed space. Live's classic Reverb is algorithmic and can't load an impulse response.

Does DAWPORT convert Fruity Convolver to Ableton?

Yes, for static settings. DAWPORT prepares a new impulse response file with Fruity Convolver's envelope, pre-delay and normalising already applied, loads it into Hybrid Reverb, and rebuilds the dry and wet levels and stereo width with Utility devices in an Audio Effect Rack.

Why was my Fruity Convolver not converted?

The most common reason is a missing impulse response. If you upload only the .flp file and the IR is a separate file on your computer, DAWPORT can't rebuild the reverb. Upload a project archive that includes the IR. Automation, a stretched IR and some other settings also keep a Fruity Convolver from converting; the notes list it.

Does Ableton's Hybrid Reverb convert to Fruity Convolver?

No. Going from Ableton to FL Studio, a Hybrid Reverb that uses its convolution section is reported as not converted. A Hybrid Reverb that uses only its algorithm section with the Dark Hall algorithm can become Fruity Reeverb 2.

Does every Ableton Live edition have Hybrid Reverb?

No. Hybrid Reverb is included in Live Suite only, according to Ableton's edition comparison. Live's classic Reverb, which is in every edition, cannot load an impulse response.

Convert now